Amorolfine hydrochloride ethosomes showed a slow release rate.
盐酸阿莫罗芬醇质体释放速度较慢。
The solutions are compared with the energy release rate of linear elasticity.
解答与线弹性的能量释放率进行了比较。
RESULTS:The granularity, water content and release rate met the requirements.
结果：本品的粒度、水分、释放度等均符合规定。
This model is based on gas release rate and jet fire model to estimate the hazard area.
该模型是基于气体释放速率和火灾模型来估计危险影响区域的。
Aim To prepare puerarin enteric nanoparticles and investigate their release rate in vitro.
目的制备葛根素肠溶纳米粒，并对其体外释放度进行考察。
The equations of loading and bounding surfaces are described in strain-energy release rate.
加载面、边界面方程均以损伤能量释放率表示。
The need to tailor release rate profiles from polymeric microspheres is a significant problem.
需要得到多聚体微球的释放率情况，这是一个非常大的难题。
Objective To determine the encapsulation efficiency and the release rate of baicalin liposome.
目的测定黄芩苷脂质体的包封率与渗漏率。
The heat release rate of TBD620V12 diesel engine is analyzed by the method of combustion analysis.
利用燃烧分析方法，对TBD620 V 12柴油机的缸内压力曲线进行了放热规律分析。
OBJECTIVE To prepare vitamin C sustained-release tablets and determine their in vitro release rate.
目的：研制维生素c微囊并制成缓释片剂，评价其体外释放特性。
Objective: To study the in vitro release rate of ambroxol HCl osmotic pump controlled release tablets.
前言：目的：研究盐酸氨溴索渗透泵控释片的体外释放度。
Objective To investigate the release rate and pharmacodynamics in vitro of of vincristine sulfate liposomes.
目的考察硫酸长春新碱脂质体的体外释放度及其药效。
The formulas for radiation densification, swelling, fission gas release rate and transient release are given.
给出了辐照密实、肿胀、裂变气体释放率和瞬时释放表达式。
To perfect the calculation, we calculated the heat release rate with the actual diagram of work after testing.
样机试验后，再根据实测示功图来计算放热率，从而完善了计算。
Numerical solution of these equations yields the intensity factors and the energy release rate at the crack tip.
求解这些方程组，获得了裂纹尖端的强度因子和能量释放率。
Methods:The release rate of ambroxol HCl osmotic pump controlled release tablets in various mediums was observed.
方法：考察渗透泵在不同介质中的释放情况。
In the case of constant load, the energy release rate will increase with time until it reaches a higher limit value.
在常载荷的情况下，能量释放率将随时间而增长，直到它达到某一较高的极限值。
In addition, mass loss rate was not the only parameter influencing heat release rate in cone calorimeter for agaric.
同时，木耳的质量损失速率不是影响其热释放速率的惟一因素。
The energy release rate for crack propagation depends only on the stress intensity factor and the material constants.
电导通裂纹模型中的静电场对裂纹尖端扩展的能量释放率不作贡献。
In the case of constant displacement, the energy release rate will decrease with time, until it reaches a lower limit value.
在常位移的情况下，能量释放率将随时间而减少，直到它达到某一较低的极限值。
The results indicate that the higher the concentration of chitosan in the capsules, the slower the release rate of capsules.
结果表明，随着胶囊中壳聚糖浓度的增大，肝素的释放速率变慢。
The varying tendencies of mass loss rate, temperatures of each point, and CO concentration were all consistent with heat release rate.
质量损失速率、各点温度以及产物一氧化碳浓度变化曲线均与热释放速率曲线的变化趋势保持一致。
The energy release rate and failure criterion for mixed mode are investigated by means of the method of equivalent linear crack extension.
利用当量直线裂纹扩展法研究复合型裂纹的能量释放率及相应的断裂判据。
Some heat release rate formulas are added to the application software for calculation on the properties of the fire smoke flow in building.
将各种非稳态火源热释放速率计算式嵌入建筑物火灾烟流性状预测软件并进行了算例验证。
Drug release rate was significantly influenced by release area, stirring speed of peddles and the sorts of dispersion mediums respectively.
释放面积，桨的搅拌速度及释放介质均影响脂质体凝胶的溶蚀及药物的释放。
The strain energy release rate of the crack propagation was calculated by using virtual crack closure technique, and fatigue life was forecasted.
采用虚拟裂纹闭合技术计算裂纹扩展的应变能释放率，并对裂纹扩展寿命进行计算。
The feasibility of oxygen-enriched combustion in diesel engines was analysed in theory from aspects of heat release rate of fuels and combustion products.
通过对燃料燃烧的放热效率及燃烧生成物进行分析，进而对柴油发动机富氧燃烧的可行性进行理论分析。
While NVP was incorporated into polymer drug, it had little effect on release in acid condition, but drug release rate in base condition increased markedly.
同时，共聚物中亲水组分—NVP的引入，对酸性条件下的释放影响不大，但明显加快了药物在碱性条件下释放。
Due analysis has been made and it is found that the nonlinear energy release rate of orthotropic plate with a, crack is dependent on the biaxial load factor.
本文分析双向加载下正交异性裂纹板的非线性能量率，指出所研究的裂纹板的非线性能量释放率与双向加载因子有关。
The general solution of the electromechanical field, intensity factors and energy release rate are obtained, which are expressed in terms of series expansion.
得到了级数形式表达的电场和弹性场的基本解、场强度因子和能量释放率。
应用推荐