Objective: to provide the anatomical data of screw diameter for the use of transpedicular screw fixation.
目的：为椎弓根内固定术选用螺钉直径提供解剖学资料。
Everything else unchanged, the bigger the screw diameter, the bigger is the depth of the screw flight in the metering section, which increases plasticizing capacity.
在螺杆的设计不变的情况下，螺杆直径越大，计量段的槽深便越深，增加了塑化能力。
Top view of roundhead slotted screw. Selection box represents thread diameter.
圆头一字槽螺钉的俯视图。选择框代表螺纹直径。
Top view of panhead slotted screw. Selection box represents thread diameter.
平头一字槽螺钉的俯视图。选择框代表螺纹直径。
Top view of countersunk slotted screw. Selection box represents thread diameter.
埋头一字槽螺钉的俯视图。选择框代表螺纹直径。
Top view of slotted head set screw. Selection box represents thread diameter.
一字槽头螺钉的俯视图。选择框代表螺纹直径。
Top view of fluted socket head set screw. Selection box represents thread diameter.
凹槽插口螺钉的俯视图。选择框代表螺纹直径。
Top view of fillister head screw. Selection box represents thread diameter.
槽头螺钉的俯视图。选择框代表螺纹直径。
Top view of bevel headed, hexagonal head set screw. Selection box represents thread diameter.
斜切六角螺钉的俯视图。选择框代表螺纹直径。
GREEN machine schedule: Daily, computerized schedule of tubing stock organized by outer diameter size, to be run on the screw machines per customer requirements.
毛坯件机加工计划：对按照外径分类好，按客户需求在车床上加工的管材的日常计算机管理计划。
Drilling, it is necessary to advance 1.5 times the diameter of the screw, the screw too tight will cause stress.
有必要事前钻孔，1.5倍于螺钉的直径，而螺钉过紧会引起压力。
The value of apparent viscosity is influenced by the diameter of the screw propeller.
用直径较大的转子测得的表观粘度较低。
Top view of cheese head slotted screw. Selection box represents thread diameter.
扁圆头一字槽螺钉的俯视图。选择框代表螺纹直径。
The machines under lesser screw length-diameter ratio possess the blending capacity of double screw extrusion under bigger length-diameter ratio.
实现了在较小的螺杆长径比的条件下达到双螺杆挤出机在较大的长径比条件下，才能达到的混炼混合作用。
Summary of Background Data. Pullout strength of a pedicle screw increases as the diameter of the screw gets larger.
背景资料概要：当椎弓根螺钉直径增加椎弓根螺钉的拔出力也会增加。
According to Terzaghi consolidation theory, the partial differential equation and filtration formula of the change diameter screw compression were induced.
根据太沙基固结理论推导出了变径螺旋压榨压方程，得出了压榨速率的表达式。
The strength of a screw fastener increases with the square of its diameter.
螺丝紧固件的拉张力随其径长呈平方增长，其扭矩则呈立方增长。
The squeezing action forces the displacer of the screw into the sheet, causing it to reduce the mounting-hole diameter and captivate the screw.
挤压动作迫使薄板金属塑性变形，并使安装孔的直径变小，从而使螺钉松不脱。
To meet the needs of tensile test for small diameter bolt and screw, this article gives a design of tensile testing device.
针对小直径螺栓和螺钉的拉伸试验要求，设计了一种拉伸试验装置。
Note: It may be necessary to drill clearance holes, twice the diameter of the screw, through the probe to accommodate projecting mounting screws.
注：可能有必要钻一个小孔，直径为螺钉的两倍大，用探头来接触突出的安装螺钉。
METHODS: Three-dimensional finite element method was used to analyze the initial stress around screw implant of different elastic modulus and different diameter.
方法：用三维有限元的方法对不同弹性模量和不同直径种植体植入后骨界面的初始应力进行分析。
Note 1 the diameter of the Screw Shaft both ends must be less than the Screw Shaft Root diameter.
注1设计时，请注意使两个轴端不超过丝杠轴底径。
Conclusion in the studied scope, the diameter of the screw showed much more influence on the stress distribution than the length did.
结论在所研究的尺寸范围内，种植体的直径对应力分布有重要影响，而种植体的长度对应力分布影响不大。
Axial pullout of the screws is determined by the diameter of the screw.
螺钉的轴向拔出力由螺钉外径决定。
Axial pullout of the screws is determined by the outer diameter of the screw.
螺钉的轴向拔出力由螺钉外径决定。
Presents the following viewpoints:the radio between the height of the nut for boiler hanger rod and the diameter of screw shall not be less than 1.
主要提出以下观点：锅炉吊杆用螺母的高度与螺纹公称直径之比不宜小于1。
Using the intraoperative planning function of the image-guided system, the largest diameter screw possible in each particular case was placed.
利用图像引导系统的术中计划的功能，针对每个病例选用最大直径的椎弓根钉。
The bimetallic thermometer should note the products model. test range, fix screw, protect pipe length, shield diameter, accuracy and other technique parameter.
双金属温度计订货时须分别注明产品的型号、测量范围、安装螺纹、保护管长度外壳直径、准确度等级等技术参数。
The bimetallic thermometer should note the products model. test range, fix screw, protect pipe length, shield diameter, accuracy and other technique parameter.
双金属温度计订货时须分别注明产品的型号、测量范围、安装螺纹、保护管长度外壳直径、准确度等级等技术参数。
应用推荐