方法2：虚拟scsi磁盘。
Two SCSI controllers and two disks
两个SCSI控制器和两个磁盘
The agent supports all SCSI II disks.
这个agent支持所有的SCSIII磁盘。
Define the virtual SCSI disk maps (VIO).
定义虚拟scsi磁盘映射(VIO)。
The typical SCSI generic driver commands.
典型的SCSI通用驱动器命令。
6 data disks using RAID 0 SCSI controller.
数据磁盘，使用RAID0SCSI控制器。
It also manages SCSI-specific error recovery.
它也负责管理特定于SCSI的错误恢复。
Table 2 shows how the SCSI standard is defined.
表2显示如何定义SCSI标准。
All SCSI commands should also contain a control byte.
并且所有SCSI命令都要包含一个控制字节。
Many drivers use these atomic operations, particularly SCSI.
许多驱动程序使用这些原子操作，特别是SCSI。
The SCSI subsystem is one of these block device drivers.
scsi子系统是这种块设备驱动器之一。
Status: SCSI status byte as defined by the SCSI standard.
status：由scsi标准定义的SCSI状态字节。
Various controllers, such as IDE and SCSI, are also supported.
支持各种控制器，比如ide和SCSI控制器。
SPC defines behaviors that are common to all SCSI device models.
SPC定义对所有scsi设备模型通用的行为。
Devices like scanners or SCSI adapters use this transfer type.
像扫描仪或者scs i适配器这样的设备使用这种传输类型。
You've created the virtual SCSI devices in the partition's profile.
您已经在该分区的概要中创建了虚拟scsi设备。
Listing 2 shows the source code clips of using the SCSI generic API.
清单2显示了使用SCSI通用API的源代码片段。
Internal storage using SCSI adapters and drives dedicated to the partition.
专用于分区的使用SCSI适配器和驱动器的内部存储器。
It USES the standard SCSI command set for interacting with SAS End devices.
它使用标准的SCSI命令集与sas端设备交互。
For example, on one of my test systems it got stuck doing SCSI detection.
例如，我的一个测试系统在检测scsi的时候挂起了。
You don't need to waste time trying to track down video drivers or SCSI drivers.
您不必将时间浪费在尝试寻找显卡驱动程序或SCSI驱动程序上。
In Figure 2, you can see how different applications communicate with SCSI devices.
在图2中，您可以看到不同的应用程序如何与SCSI设备通信。
The mid level also provides SCSI command queuing between the upper and lower levels.
中间层还提供了较高层和较低层间的SCSI命令排队。
Virtual storage using a virtual SCSI adapter and storage in a different partition.
使用虚拟scs i适配器的虚拟存储器和不同分区中的存储器。
The storage often acts as a SCSI target that receives and processes SCSI commands.
存储介质通常充当SCSI目标，它接收和处理 SCSI命令。
An inquiry command is the most common SCSI command that all SCSI devices implement.
inquiry命令是所有SCSI设备实现的最常用的SCSI命令。
The virtual target devices and virtual SCSI adapters are created on the target system.
在目标系统上创建虚拟目标设备和虚拟scs i适配器。
The first SCSI standard, called SCSI-1, was created by Shugart Associates around 1979.
第一种SCSI标准称为SCSI - 1，是由Shugart Associates在1979年前后创建的。
Open the SCSI generic device file (such as sg1) to get the file descriptor of SCSI device.
打开SCSI通用设备文件(比如sg1)获取SCSI设备的文件描述符。
Figure 4 shows that the LPAR is configured with virtual Ethernet and virtual SCSI adapters.
图4显示这个LPAR配置了虚拟以太网和虚拟scs i适配器。
应用推荐