The design of AMPS reactors was presented, some noticeable problems in design and manufacture were proposed for the particular structure using the magnetic driving seal in the shaft seal.
介绍了AMPS反应釜的设计，针对轴封采用磁力传动密封的特殊结构，指出了在设计和制造中应注意的问题。
Mechanical seal: seal face, gasket and shaft seal, etc parts must be undamaged, otherwise will result in over leakage, sure to change parts with wear and tear or damage.
机械密封：密封面、密封垫及轴封等元件必须完好，否则将导致过度泄漏，对有磨损或损伤的元件必须更换。
Pump shaft seals use mechanical seal, pump top and bottom, respectively, equipped with water injection plug and the drain plug.
泵的轴封采用机械密封，泵体顶部和底部分别装有注水、放泄的螺塞。
Basic structure of the centrifugal pump is composed of six parts, namely: impeller, pump, pump shaft, bearing, seal ring, stuffing box.
离心泵的基本构造是由六部分组成的，分别是：叶轮，泵体，泵轴，轴承，密封环，填料函。
The pump comprises mainly of pump body, cover, impeller, shaft, seal ring, intermediate support, sealing and suspension assembly, etc.
泵主要由泵体、泵盖、叶轮、轴、密封环、中间支架、密封和悬架部件等组成。
PW, PWF mainly by the pump cover, pump casing, impeller, shaft seal, shaft, and bracket the composition of such components.
PWF主要由泵盖、泵壳、叶轮、轴封、轴、和托架等零部件组成。
By means of optimizing seal construction and packing material, the shaft seal technique of polypropylene polymerizer in this plant are deeply researched.
从填料密封结构的优化、填料的优选对本厂聚丙烯聚合釜轴封技术进行了深入的研究。
The shaft seal leakage, judgement and emergency measures of the final polycondensation reactor was introduced.
介绍了终缩聚反应器轴封泄漏的现象、判断和应急措施。
Improving measures are put forword against the phenomenon of shaft end seal of oil leakage of centrifugal fan driving unit.
针对离心通风机传动组的轴端密封经常漏油这一现象，提出了改进措施。
The article further poses design thoughts of liquid charge pump which have not shaft seal contact.
进一步提出了轴封不接触泥浆灌注泵的设计思想。
The principle of magnetic-fluid reciprocating shaft seal is introduced, some problems of its design and application are analyzed from the point of view of tribological design.
介绍了磁流体往复轴密封的原理，从摩擦学设计角度分析了其设计和使用中要注意的问题。
This paper presents experimental results for shaft seal assembly with three kinds of different support seats.
本文介绍了三组不同支座的轴密封部件试验结果。
Prior to startup, get rid of tape from labyrinth seal end of input shaft, labyrinth seal outer surface of output drive flange and respirator.
启动前应除去减速机输入轴迷宫密封端面和输出传动法兰迷宫密封外圆表面，以及呼吸器上的防锈包装及胶带。
The machine imports, pumps, pump shell structure strong are the hydrostatic test, the mechanical shaft seal, stop leakage effect is good.
整机进口，泵浦结构坚固，泵壳皆经水压试验，采用机械轴封，止漏效果好。
Shaft seal: mechanical seal, according to user requirements can be used seal packing.
轴封：采用机械密封，根据用户要求也可以采用填料密封。
The shaft sleeve and mechanical seal can be replaced without removing the shaft from the pump.
轴套和机封的更换不必将轴从泵上拆下来。
We should open and check the shaft seal. If it leaks, then replace it, if necessary.
应该拆检轴封。如果发生漏泄，有必要就换掉它。
Pump shaft seal is designed to end in two forms, one for the mechanical seal, one is packing seal, may be based on specific usage and user requirements to determine.
泵轴端密封设计为两种形式，一种为机械密封，一种是填料密封，可根据具体使用情况和用户要求确定。
The main shaft seal of pump turbines with large capacity at high rotational speed is more liable to failure as compared with that of conventional pump turbines.
大容量、高转速水泵水轮机主轴密封相对常规水轮机主轴密封更容易发生故障。
In this article, several key points in the reform of the shaft seal used in the rotary disc tower were analyzed.
本文分析了带旋转轴塔轴封改造中应注意的几个关键问题。
Main components: two-rotor, the body, the main bearings, shaft seal, balance and energy-conditioning Pistons.
主要部件：双转子、机体、主轴承、轴封、平衡活塞及能量调节装置。
Through the status analysis on shaft seal system of 9E combined-cycle steam turbine, the improvement for shaft seal overflow is put forward to save energy and reduce consumption.
通过对9E联合循环汽轮机轴封系统的现状分析，提出对轴封溢流的改造以达到节能降耗的目的。
Models shown are highly recommended where a large mechanical or rotary shaft seal is required, and low noise levels are important.
这个型号强烈的推荐大型的机械或旋转密封轴是必需的，低噪音标准很重要。
Most pumps used in vegetable oil plants often fail to work due to the leaking of shaft seal.
植物油厂用泵现场使用表明，大部分泵的失效是由于密封泄漏引起的。
The pump consists of three sections from bottom to top: the hydraulic section, the shaft seal section and the motor section.
主泵由三个部分组成(由下而上)：水力部件，轴密封部件和电机部件。
A new muddy packing is investigated by analyzing principle of packing seal and comparing with other shaft seal materials in pumps.
以新型泥状填料为研究对象，通过对密封原理的分析及新老泵类轴端密封材料性能的比较，从而得出两代密封材料的优缺点。
This fact does not contact the shaft seal surface, it is the sealing principle of polymer cooled to half molten state and forming the seal.
这种密封实际上并不接触轴的表面，它的密封原理是将聚合物冷却到半熔融状态而形成自密封。
This fact does not contact the shaft seal surface, it is the sealing principle of polymer cooled to half molten state and forming the seal.
这种密封实际上并不接触轴的表面，它的密封原理是将聚合物冷却到半熔融状态而形成自密封。
应用推荐