The concern of pump is the increased thermal cycling and vibratory loads.
泵的关注增加的热循环和振动载荷。
The thermal cycling test of divertor target plate was carried out in the vacuum;
在真空室中用大功率电子束作为热源进行了热疲劳试验。
The thermal cycling effect on silicon solar cell structure was studied in the paper.
试验研究了太阳电池结构的热循环效应。
Thermal cycling is an important factor to determine structure and property of HAZ after welding.
热影响区的热循环是决定焊后热影响区组织和性能的重要因素。
Then they searched for DNA amplification enzymes that could operate at that thermal cycling speed.
然后他们再寻找能够在这种环境正常工作的放大酶。
Then thermal cycling stability and radiation exposure experiments are performed to simulate the space environment.
然后，分别进行了热循环实验与射线辐照实验。
Thermal cycling on-line measuring method was proposed to evaluate the dimensional stability of metal materials unloaded.
提出了对金属材料在无负载条件下进行尺寸稳定性评定的热循环在线检测法。
Unique thermal cycling system, sub-cold water, hot water and a washable feature high cleaning power, convenient and practical.
独特的热循环系统，分冷水，热水兼可洗涤功能，洗净力高，方便实用。
Oxidation happened on the surface of infiltrated layer when thermal cycling times was less than 20, and no cracks was observed.
结果表明：热循环次数小于20次时，渗层表面主要产生氧化，无裂纹产生；
Using this model the permanent distortion and work life in long term under thermal cycling can be predicted based on a few test data.
利用该模型，根据少量试验数据可预示长期冷热循环下的永久变形或工作寿命。
But the strain under compound condition is not only simply addition of that under random vibration and thermal cycling load condition.
此外，复合载荷条件下的应变值也并非随机振动和热循环载荷情况下两种应变值简单的相加。
AZ91D magnesium alloy was welded using TIG method, and the influence of welding thermal cycling on the hardness of AZ91D alloy was studied.
采用tig焊接方法焊接AZ 91 d镁合金，考察了焊接热循环对镁合金的硬度的影响。
In this paper, using ground-based simulation facilities, the vacuum thermal cycling test was carried out on the epoxy construction adhesive.
本文利用空间环境效应地面模拟设备对环氧结构胶粘剂进行了真空热循环试验。
On the basis of relationship between permanent distortion and thermal cycling number, we present mathematical model in terms of power function.
根据实测的永久变形与温度循环次数的关系，提出了一个幂函数的数学模型。
Finally, a thermal cycling test completed in vacuum on a carbon fibre parabolic antenna reflector is also deseribed, and the results of the measure…
最后进行了碳纤维抛物面天线反射器的真空冷热交变试验。
Multiphysics tools from ANSYS enable product designers to examine thermomechanical stresses in packages and boards that develop during thermal cycling.
ANSYS的多物理场工具模块能够帮助产品设计者检测热循环过程中在装置内部和基板之间的热压力。
Thermal cycling absorption process(TCAP) in a full reflux mode was studied at different feeding ratios, feeding places and heating/cooling temperatures.
分别在不同进料比、进料位置、加热/冷却温度的条件下，对TCAP工艺的全回流模式进行了实验。
Threaded seat rings should be lock welded to the body when used in high velocity (turbulent) or thermal cycling services to avoid loosening. Please specify.
当用于高速流体（湍流）或热循环应用时，为了避免松开，螺纹阀座环应该锁焊在阀体上。请在订购时加以指定说明。
Threaded seat rings for valves in services with high velocity turbulent flow or thermal cycling should be lock welded to the body to avoid loosening. Please specify.
如果阀门用在高速流体(湍流)或热循环应用环境中，则螺纹阀座环应该锁焊到阀体上，避免松落。请在订购时加以指定说明。
The results show that the matrix in the microstructure occurs dynamic recovery and recrystallization and the materials generate cyclic softening during thermal cycling.
结果表明，在热循环过程中基体组织发生动态回复和再结晶，材料产生循环软化；
This paper presents a new designed thermal cycling heater system for PCR in microfluidic chip. It includes the power design, the control project and algorithm experiment.
介绍了一种适用于微流控芯片P CR扩增的新型循环加热系统，包括系统可控电源电路设计、控制方案确定及控制算法实验。
The incubation period of crack nucleation decreases and the crack propagation rate increases with the increase of thermal cycling temperature and cooling rate in the cycle.
随循环温度和冷却速率的增加，裂纹形核的孕育期缩短，裂纹扩展速率增加。
The tensile properties and microstructure of LF6 aluminum alloy weld joint under simulating near earth space environment are studied by means of vacuum thermal cycling system.
采用真空热循环试验装置，模拟近地轨道空间环境，研究了LF 6铝合金焊接接头拉伸性能和微观组织，分析讨论了真空热循环对焊接接头的影响规律。
Among all hydrogen isotope separation technologies, Thermal Cycling Absorption process (TCAP), a semi-continuous hydrogen isotope separation process, is of many unique advantages.
热循环吸附工艺(TCAP)是一种半连续的氢同位素分离方法，在分离氢同位素方面有许多独特的优越性。
The rules of dimension change of plastic bonded explosive PBX TATB charges during thermal cycling were studied in detail, and the methods of reducing the permanent expansion were studied.
研究了塑料粘结炸药PB X TAT B药柱在热循环过程中的尺寸变化规律，探索了减小永久性长大的方法。
The sequential thermal cycling (TC) and drop impact test is more reasonable to evaluate the reliability of lead-free solder interconnections compared with single TC test or drop impact test.
焊料微互连在热周期和跌落冲击顺序载荷下的可靠性研究更具有实际意义。
The paper discusses the importance and implementation of various types of thermal tests (thermal balance test, thermal vacuum test and thermal cycling test) during the spacecraft development phase.
论述了各种类型热试验（热平衡试验、热真空试验、热循环试验）在航天器研制中的重要性及它们的做法要点。
The paper discusses the importance and implementation of various types of thermal tests (thermal balance test, thermal vacuum test and thermal cycling test) during the spacecraft development phase.
论述了各种类型热试验（热平衡试验、热真空试验、热循环试验）在航天器研制中的重要性及它们的做法要点。
应用推荐