Install IAC motor to throttle body.
安装IAC马达至节气阀体。
From mass flow sensor, then, does it goes to the throttle body.
从质量流量传感器，那么，它是否去节流机构。
Throttle Body Assemblies described here use an aluminum casting.
这里描述的节气门体组件使用的铝铸件。
The mass of the Throttle body assembly is defined on the outline drawing.
风门装配的质量已在轮廓图中标出。
A component, such as an intake manifold or a throttle body, has an air passage.
一种部件，例如进气歧管或节气门本体，具有空气通道。
The Throttle body contains bearings for mounting the Throttle Shaft across the bore.
节气门体包含横跨镗孔、用于安装节气门轴的轴承。
The Throttle body has a by pass hole and IACV for meeting the idle airflow requirement of the engine.
节气门体有一个节流孔和IACV，以满足发动机怠速气流要求。
Throttle body made from high temperature and high pressure liquid into the evaporator of refrigeration.
节流机构使制冷从高温高压液体进入蒸发器。
This cell was manufactured to build and full function test a throttle body for the automotive industry.
该元件制造用于为自动化工业建造和全功能测试，为汽车行业节气门。
The dimensions of the Throttle body assembly are defined on the Throttle body assembly outline drawing.
风门装配的尺寸如风门装配轮廓图所示。
The Throttle body Assembly is designed to withstand the following functional and environmental durability tests.
风门装配的设计可承受如下功能，环境耐久试验。
The Throttle body assembly shall meet all performance requirements listed herein at the normal operating conditions.
在正常操作条件下，节气门体总成必须满足本文所列的所有性能要求。
The Throttle body provides surfaces for mounting between the Motorcycle's air intake duct and the engine intake manifold.
风门表面留有安装摩托车进气管和发动机进气歧管的位置。
The test results indicate that the throttle body assembly can meet the durability and reliability requirements of motorcycle.
试验结果表明节气门总成能够满足摩托车对耐久性和可靠性要求；
A single 52mm throttle body sits atop a plastic intake manifold and feeds a common chamber, which in turn feeds six long intake runners.
一个单一的52mm油门机构坐落在一个塑料进气歧管，养一个共同的工作室进而促进六长进气赛跑选手。
The throttle body is usually located between the air filter box and the intake manifold, and it is usually located near the mass airflow sensor.
节气门体之间通常是位于空气滤清器箱和进气歧管，通常是位于大规模气流传感器。冷空气摄入量和它如何运作的。
Throttle body. The throttle body is the part of the air intake system that controls the amount of air flowing into an engine's combustion chamber.
节气门体，同时就节气门体的进气系统的一部分，控制适当的气流流动到发动机的燃烧室。
A return switch (RS) is responsive to the motor throttle body, and a pressure sensitive switch (PSS) is responsive to the accelerator pedal position.
返回开关(RS)是顺应电机油门身体，压力感应开关(PSS)的回应是由于油门踏板的位置。
An air duct will mount to the Throttle body assembly air intake snout. The snout lip dimensions are defined on the Throttle body assembly outline drawing.
气管加装在风门装配进气口上。进气口尺寸如风门装配轮廓图所示。
The Throttle body assembly will mount to the manifold snout and intake manifold interface dimensions are defined on the Throttle body assembly outline drawing.
节气门体总成安装在歧管口，进气歧管接口尺寸如节气门体总成轮廓图所示。
It is difficult to see throttle body growth, and our growth as a company, slowed by something as small as the order quantity for part on the initial order only.
很难看到作为一个成长中的公司由于其定量这样的小问题而被遏制成长。
A continuous throttle regulation device employs a motor throttle body located proximate to a motor or engine, and an accelerator pedal located remote from the motor or engine.
连续节流调节装置采用了位于汽车节气门体就近汽车或引擎，以及油门踏板离汽车或引擎远程。
High pressure fluid through the filter, the gush after the throttle body into the evaporator, and in the corresponding under low pressure, the quantity of heat of evaporation from around.
高压液体经过过滤器、节流机构后喷入蒸发器，并在相应的低压下蒸发，吸取周围的热量。
Disconnect the accelerator cable, the cruise control cable (if equipped), and the transmission line pressure cable (if equipped) from the throttle body and remove them from the cable bracket.
从节流阀体上拆下加速器电缆、车速控制电缆(若已装备)、及变速箱管线压力电缆(若已装备)，并将它们从电缆托架上拆除。
Disconnect the accelerator cable, the cruise control cable (if equipped), and the transmission line pressure cable (if equipped) from the throttle body and remove them from the cable bracket.
从节流阀体上拆下加速器电缆、车速控制电缆(若已装备)、及变速箱管线压力电缆(若已装备)，并将它们从电缆托架上拆除。
应用推荐