To analyze the influence of factors such as monomer and initiator to the polymer limiting viscosity number and the monomer conversion rate.
分析了单体、引发剂等因素对聚合物特性粘数和单体转化率的影响。
Viscosity number determination of polyvinyl chloride resin dilute solution is one of the important indexes on polyvinyl chloride resin and determines its various USES.
聚氯乙烯树脂稀溶液粘数是聚氯乙烯树脂的一项重要指标，它的高低决定着产品的不同用途。
The effect of montmorillonite nano-meter particle on the thermostability, mechanical properties and intrinsic viscosity number of the nano-meter composite was studied.
研究了蒙脱土纳米粒子对复合材料热稳定性、力学性能和特性粘数的影响。
As can be seen from flocculation test of CPAM on coal slurry, intrinsic viscosity number, cation degree and medical dosage of CP AM have obvious effect on flocculating performance.
由CPAM沉降煤泥水的絮凝试验可知，CPAM的特性黏数，阳离子度以及药剂用量对煤泥水的絮凝效果都有很大影响。
If you have a high viscosity, it's very sticky, then this number, C1 So this we call the viscous term, and this we call the pressure term.
如果粘性高，它非常粘稠，这个数值，会变得很高。，C 1, will, be, very, high。，所以我们叫它粘性项，这个我们叫做压力项。
The results also showed that the delignification rate and the reduction rate of viscosity decreased as the Kappa number of bamboo EMCC pulp decreased.
研究结果也表明，深度脱木素竹浆氧脱木素，木素脱除率和黏度降低率都随着原浆卡伯值的降低逐渐减小。
The viscosity of Gemini surfactants solution is also related to the alkyl carbon number and the spacer.
双子表面活性剂的溶液粘度与烷基链和联结基的长度有关。
By using two-structure linear combination model, the asymmetric broadening of RDF, the coordination number, the bond Angle distribution and the viscosity of chlorides have also been discussed.
通过两结构模型对径向分布函数非对称展宽、配位数、键角分布和粘度作了讨论。
After treatment, the number of lung cancer metastasis, whole blood low shear viscosity, whole blood high shear viscosity and aggregation index of red blood cells (RBC) were observed.
各组药物治疗后检测肿瘤肺转移灶个数和全血低切黏度、全血高切黏度、红细胞聚集指数。
Results show that an increase of ions with 4-coordination number in molten slag makes the bulk viscosity increasing, while that with 6-coordination number is contrary.
结果表明随着熔渣中四配位离子的增加，其体相粘度增加，而六配位离子的作用则相反。
The results show that the infiltration volume in feeding process increases with increasing the feeding time and velocity or decreasing the fluid viscosity and eyelet number of porous medium.
结果表明：随着补缩时间和旋转速度的增加，补缩过程中渗流流体体积增大；
The results show that the infiltration volume in feeding process increases with increasing the feeding time and velocity or decreasing the fluid viscosity and eyelet number of porous medium.
结果表明：随着补缩时间和旋转速度的增加，补缩过程中渗流流体体积增大；
应用推荐