骨—HA界面的最大剪切强度。
剪切强度等于物质的内聚力。
考察了粘砂套管剪切强度的影响因素。
Factors affecting the shearing strength of cemented casing are investigated.
且注入剂量不同，其焊缝的剪切强度存在着较大差异。
And there is a distinct difference between the shear strength of welding seams with different implantation fluence.
环氧胶粘剂的耐蚀性能是通过测定其拉伸剪切强度来评定的。
The corrosion resistance of epoxy adhesive was assessed by its tensile shear strength.
冷镦头剧烈变形能力与合金组织、塑性和剪切强度关系较大。
Big deformability was more related with its microstructure, plasticity, and shear strength.
目的对光固化和化学固化树脂粘接剂的剪切强度进行对比研究。
Objective To compare the shear bond strength of light cured and chemically cured resin adhesive.
而对于反复煮沸压缩剪切强度，桦木的值要比落叶松和柞木的高。
The dry compressing shear strength of Larch in normal conditions was the lowest.
当混凝土浇筑在平滑的岩石表面时，地基上的剪切强度可能会减少。
The shearing strength at the foundation, where the concrete is placed on a smooth rock surface, may be lessened.
单纤维段裂试验作为复合材料界面剪切强度的一种测试方法被沿用至今。
The single fiber fragmentation test has been used to determine the interfacial shear strength of composite materials.
结果随着碳纤维含量的增加，根管桩的弯曲强度和剪切强度均逐渐增加。
Results the transverse strength and shear strength were increased with the increase of the carbon fiber content.
粘接剂主要以剪切的方式破坏，粘接剂剪切强度是一个值得注意的问题。
Attention should be paid to the shear strength of the adhesives since the shear stress could cause failure in the adhesive layer.
测试了剪切力分别沿根尖方向和切缘方向作用的静剪切和冲击剪切强度。
The dead load shear and impact shear testing were performed from both of root apex direction and cutting edge direction.
考察了金属化工艺、镀镍及镀后热处理对接头剪切强度和钎焊效果的影响。
Influences of the metallizing technologic conditions, Ni plating and subsequent annealing on the joint shear strength were investigated.
目的：研究三种不同釉质粘接剂对陶瓷托槽与瓷修复体粘接剪切强度的影响。
Objective: to investigate the shear bond strength of three adhesive systems bonded with ceramic brackets to the porcelain surfaces.
介绍了三种典型的圆片键合强度表现形式：抗拉强度、剪切强度和粘接强度。
Three typical manifestations of wafer bonding strength were introduced as tensile strength, shear strength and adhesive strength.
离聚体的拉伸强度、搭接剪切强度和乳化性能均随顺酐化程度的提高而改善。
Tensile strength and lap shear strength increased with increasing of grafting degree due to great improvement of polarity.
总结出剪切屈服强度和拉伸屈服强度，最大剪切强度和抗拉强度之间的关系。
Draw the conclusion that the relationship between the shear yield strength and yield strength, between the ultimate shear strength and the ultimate strength.
再对斑脱土衬里进行三轴固结不排水实验，测定其总剪切强度与有效剪切强度。
Triaxial shear tests were also conducted on the two liner specimens to obtain the total and effective shear strength.
目的：研究不同酸蚀时间和不同施力方向对正畸托槽与牙面间剪切强度的影响。
Objective: the aim of the study was to investigate the effects of different etching time on shear bonding strength to guide its clinical use.
目的：研究三种牙本质脱敏剂处理牙本质表面后对全酸蚀粘接剂剪切强度的影响。
Objective: to evaluate the influence of three dentin desensitizers on shear bond strengths of a total-etch adhesive to dentin surfaces.
结果表明，桐油改性酚醛树脂的剪切强度、冲击强度较未改性树脂大，硬度适中。
The results showed that the shear strength and impact strength were superior to those of pure resin, and the hardness was mezzo.
研究表明，利用微波固化环氧胶时，不仅固化时间短，而且剪切强度优于加热固化。
The result showed that, in comparison with cure by heating, the microwave curing was much faster and obtained better shear strength.
通过剪切强度的测试评价了其对复合树脂与钛合金、钴铬合金之间的粘接所起到的作用。
The effect of this product on the bond durability of composite resin joined to Ti alloy or Co-Cr alloy was evaluated.
研究了不同搭接接头形式，胶粘剂毛边和拉伸剪切强度的测试方法对拉伸剪切强度的影响。
The effects different joint forms, queer out and the measuring ways on tensile sheer strength are studied in the paper.
通过对钢筋混凝土构件抗剪强度和抗弯强度关系的分析，能找出剪切强度控制区的下包络线。
The lower enveloping curve of the shear strength control zone can be found from the analysis of shear and flexural strength of reinforced concrete member.
提出了一种利用拉伸法和剪切法测定内生复合板钢板弱界面拉伸强度及剪切强度的测试方法。
A new method was given to test the cohesion strength of weak interface of DISC by tensile tests and shearing tests.
通过PV C -MBS片材的热粘合样品的剪切强度试验，也可观察它们界面的相容程度。
The interfacial compatibility can also be observed through the shear strength test of the PVC-MBS heat adhesive sheet.
定义溶洞顶板稳定性安全系数为顶板岩体实际剪切强度与折减到临界破坏时的剪切强度之比值。
The safety factor of karst cave roof is defined as the ratio of actual shear strength parameter to critical failure shear strength parameter in this paper.
定义溶洞顶板稳定性安全系数为顶板岩体实际剪切强度与折减到临界破坏时的剪切强度之比值。
The safety factor of karst cave roof is defined as the ratio of actual shear strength parameter to critical failure shear strength parameter in this paper.
应用推荐