建立有限元模型。
本文研究了桅杆结构非线性有限元模型的建立方法。
In this dissertation, nonlinear finite element model establishment method of the guyed mast is studied.
建立集装箱起重机结构的有限元模型。用于有限元分析。
Build finite element model of main structure of container crane for finite element analyse.
利用ANSYS软件建立了剑杆织机机架的有限元模型。
The FEM model of rapier loom frame is established with ANSYS software.
SH波数值分析表明本文有限元模型具有多向波动透射能力。
The SH numerical example shows that this new artificial boundary element has a multi-directional transmitting property.
最终得出在预测轨枕辐射噪声时，轨枕梁有限元模型更加适合。
In the prediction of sleeper radiation noise, the finite element beam model of sleeper is more suitable.
同时，根据这一试验模型的设计图纸建立了相应的初始有限元模型。
Meanwhile, based on design papers of the test model, corresponding finite element model has been established.
在考虑这一特点的基础上，建立了套管应力计算的力学及有限元模型。
Based on this point, the mechanics and finite element models for casing stress calculation are established.
介绍了轴对称场的有限元模型及其用于计算金属内部磁场分布的结果。
Briefly introduces the finite element model of axisymmetric field and the results of magnetic field calculation in metal.
提出了合理的人工边界反射系数公式，为有限元模型提供了理论基础。
A reasonable spurious parameter of artificial boundary is also proposed, which lays down the base for FEM numerical simulation.
实践表明，这种外挂物有限元模型是适合工程应用的简洁明了的模型。
It has been shown that this model is a simple and available to application in engineering.
本文建立索梁及索塔锚固的三维有限元模型，分析这些部位的局部应力。
This paper analyzes the local stress in the anchorage zone of cable-beam and cable-tower with three-dimensional finite element model for providing the reference to similar works.
有限元模型比知识的获取和形式化是有限元模型化专家系统建立的核心。
The knowledge acquisition is the 'bottleneck 'in the development of finite element modeling expert system.
建立了滑动轴承油膜的有限元模型，分析了油膜对船舶轴系轴承反力的影响。
The finite element model of the oil films was established. The influence of oil films on the reactions of marine shaft system was analyzed.
建立了滑动轴承油膜的有限元模型，分析了油膜对船舶轴系轴承反力的影响。
It is analyzed for the influence of oil films on the reactions of Marine shaft system by establishing the finite element model of the oil films.
为你自己证明这点的最好方法是生成一个简单的有限元模型，并检查输出结果。
The best way to prove it to yourself is to make a simple finite element model and check out the results.
对研究花键冷滚压成形过程中的接触面积和有限元模型的简化具有重要的意义。
It is significant to study the contact area in rolling process and simplify model of finite element.
首先建立发动机总成有限元模型，通过模态分析，为发动机的结构修改提供依据。
First establish finite element model of engine assembly, and provide evidence for the structure modification of engine through mode analysis.
实验表明，研究的新算法用于四面体单元的有限元模型，具有良好的切割处理效果。
Experiment results show that using this new algorithm for tetrahedron, finite element model can provide well visual result.
并基于此，建立整车的有限元模型，包括车架、发动机、悬架、轮胎、乘员、油箱等。
On the basis of this, the integrated finite element model of motorcycle has been established including frame, engine, suspension, wheel, rider and oil box etc.
采用实测轮胎荷载建立有限元模型，分析了满足长寿命路面要求的沥青路面结构组合。
Finite Element model was developed with actual tyre loads to analyze asphalt pavement structural combinations meeting the standards of perpetual pavement.
本文用有限元模型分析了钢筋混凝土浅圆仓仓顶的弹性稳定性，计算了其屈曲临界荷载。
In this paper, the elastic stability of reinforced concrete silo shell roof is analyzed using finite-element model. The elastic critical buckling loads of the shell roof are calculated.
结合大型有限元软件ANSYS，建立了筏形基础地基相互作用体系的全三维有限元模型。
Using general-purpose finite element program ANSYS, a three-dimensional finite element model of interaction between raft foundation and groundwork soil is established.
通过APDL语言实现有限元模型的参数化设计，计算出并联机床在工作空间内的刚度分布。
The FEA model was parameterized by APDL language and the stiffness distribution was computed over the workspace.
本文将理论、软件工具和实验有机结合起来，建立了合适、正确的这种特殊结构的有限元模型。
This paper integrated the theory, software with the experiment and established a reasonable, proper FEA model.
将吊臂截面作为整体考虑，建立了吊臂结构局部稳定性计算的参数化有限元模型和参数优化模型。
Considering the boom cross section as a whole, a parametric finite element model and a parametric optimization model for local stability calculation of a boom structure were established.
建立了既考虑发电机内部非线性又考虑外部电路拓扑结构的用于系统动态分析的时步有限元模型。
The time-stepping FEM model for the dynamic analysis of power system is established considering the nonlinear characteristics of internal generators and typology structures of external circuit.
方法采用螺旋CT扫描、计算机图像处理及CAD技术，建立含腭部种植体的上颌骨三维有限元模型。
Methods A three-dimensional finite element model of maxilla containing palatal implant was built using spiral CT scanning, computer image processing, and CAD technology.
方法采用螺旋CT扫描、计算机图像处理及CAD技术，建立含腭部种植体的上颌骨三维有限元模型。
Methods A three-dimensional finite element model of maxilla containing palatal implant was built using spiral CT scanning, computer image processing, and CAD technology.
应用推荐