叙述了化学混凝气浮法处理浸润剂污水方法的确定、处理过程及处理方法。
This paper introduced the method to treat soak-agent wastewater by chemical coagulating-gas- suspension, The treating process and the treating method.
从玻纤生产各工序出发，并以浸润剂技术为重点，分析了玻纤毛丝产生的原因。
The causes of fuzz formation in each step of glass fiber production were analyzed, with sizing technology as a focal point.
表面涂覆硅烷基浸润剂，适用于增强环氧树脂，可用于缠绕、拉剂等玻璃钢成型工艺。
It is coated with a silane-based size and is designed for reinforcing epoxy resin with filament winding and pultrusion processes.
本文介绍最近研制出的一种既适合分离和浓缩中碱又适合无碱玻璃纤维浸润剂废水的新型超滤膜。
A new type ultrafiltration membrane was prepared, and it is not only suitable for separation and concentration of the middle-alkali but also the non-alkali galss fiber lubricant wastewater.
并且淀粉型生产、加工工艺复杂，玻纤纱退解织造时浸润剂膜易散落、飞扬，有碍于卫生和健康。
The process of starch production is intricate, and the diffusion of the yarn size film produced by the process of the yarn is poisonous to the human health.
因此，建立一套先进的浸润剂生产过程监控系统是改变浸润剂生产现状、提高玻璃纤维产品质量的必要手段。
Therefore, set up an advanced production process monitoring system is a necessary method to change the soak agent production status and improve the product quality of fiberglass.
本文从浸润剂原材料的选择、拉丝工艺和烘干工艺三方面分析了浸润剂迁移现象产生的原因及其对短切毡的影响。
In this paper, the causes of size migration and its effects on chopped strand MATS are analyzed from aspects of raw material selection, fiber drawing process and fiber drying process.
介绍了增强型浸润剂在使用过程中产生的沉淀对生产和产品质量造成的影响，系统分析了可能产生沉淀的各方面原因。
Effects of precipitates formed in reinforcing size during its use on glass fiber production and product quality are described, and various possible causes for precipitation analyzed.
经SEM和FT-IR的研究结果表明：在浸润剂中添加了成膜剂后，复合材料的界面可以达到良好的结合状态，材料的力学性能也有明显提高。
The results of SEM and FT-IR suggest that good adhesion in the interfaces of composites is observed and mechanical properties are improved by adding special film-forming agent into immersion agent .
通过采用有机钛酸酯和硅烷偶联剂对导电纤维进行改性，从而提高EP对导电纤维的浸润能力。
The soakage ability of EP to the conductive fiber was improved by adding coupling agent (organic titanate and silane) to deal with conductive fibers.
结合催化剂表面天然硫酸盐的生成，对更换催化剂和高比值浸润问题进行论述。
The issues of catalyst replacement and high ratio soaks are discussed within the context of natural catalyst sulphate.
对所有粘结剂粘结的首先要求，就是必须能浸润基材。
The first requirement for any adhesive bond is that the adhesive most wet the substrate.
该成膜剂有效提高玻纤的浸润性、硬挺性，以适应FRP新工艺对玻纤的要求。
It increased effectively the impregnation, stiffness of glass fiber, so as to meet the requirements of new technique of FRP.
渗透剂JFC亦可适用于制革工艺各工序的使用，促进皮革浸润以及相关化料的渗透。
Penetrant JFC can also be used in tanning process the use of each process and promotes the leather infiltration and related material of infiltration.
用惰性吸收剂浸润。
用惰性吸收剂浸润。
应用推荐