Although there is no yield point, one needs to be defined.
虽然不能具体定义屈服点，但是必须确定下来。
Accordingly I, suggested to him, yield point of his scrape together.
因此我，给他建议了一下，让他东拼西凑点。
Silicon can obviously improve the elastic limit, yield point and tensile strength of steel.
硅能显著进步钢的弹性极限，屈从点和抗拉强度，故普遍用于作弹簧钢。
When the stress reaches the yield point, a large increase in strain occurs with no increase in stress.
当应力达到屈服点，应变会急剧增大而应力保持不变。
Therefore, under the 1900 - point market with a dividend yield point of view of a reasonable valuation.
因此，在1900年与一个合理的估值观点股息收益率逐点市场。
The yield point represents the dividing line or transition from the elastic to the plastic region of the curve.
屈服点是弹性变形区域到塑性变形区域之间曲线的过渡点。
The yield point is based on the evolution crack on CT scale and the meso process of soft rock before the streng...
软岩屈服现象的本质是CT尺度裂纹演化，裂纹演化是软岩在峰值强度前的主要细观过程。
The stress strain curves displayed the characteristics of low yield point, continuous yield and no obvious yield point.
结果表明 ：其应力—应变曲线表现出屈服点低、连续屈服、没有明显的屈服点等特性 ；
The value of stress under air pressure test shall not exceed 80% of the yield point of the material in test temperature;
气体压力试验时的应力值，不得超过试验温度下材料屈服点的80%。
It was observed that the lower yield point was subject to a greater degree of scatter than that of the upper yield point.
业已观察到下屈服点比上屈服点易产生更大的散布度。
From the yield point of view, the performance of Xingyu 3 was good, followed by Xingyu 2, which should be greatly promoted.
从产量水平来看，兴芋3号表现较好，其次为兴芋2号，可加大力度推广。
Because of the lower yield point of rotor material, the local plastic deformations are found during operation at rate speed.
由于转子材料屈服点较低，在额定转速时，局部会出现塑性形变。
The value of stress under hydraulic pressure test shall not exceed 90% of the yield point of the material in test temperature;
液体压力试验时的应力值，不得超过试验温度下材料屈服点的90%；
When the material does not display a yield point, a quantity known as the proof stress is used when making design calculations.
当材料不显示屈服点时，在进行设计计算中，往往使用所谓弹性极限这一数值。
When the material does not display a yield point, a quantity known as the proof stress is used when making design calculations.
在二维或三维的情况下，屈服极限是当所有应力分量的某个函数达到某一固定值时达到的。
When the material does not display a yield point, a quantity known as the proof stress is used when making design calculations.
文中证明，特征线法的应力关系式与本文的屈服条件、屈服函数的极值条件是相同的。
It must be emphasized that the absence of a definite yield point does not in itself imply that the material has a low ductility.
必须强调的是，没有明显的屈服点并不意味材料有较低的韧性。
Harvested area error of yield point is one of the main reasons to bring yield error in yield data collected by yield monitoring system.
采样周期内实际收割面积计算误差造成的产量数据误差是联合收割机计产数据中的一种常见误差。
Beyond the yield point, the material will continue to deform, but with less stress than before, because the material has begun to yield.
超过屈服点之后，材料会继续变形，但是因为材料开始屈服，应力会减小。
The volume dilatation and the non-linear deformation of rock originated, when the differential stress equals to the yield point of rock.
当差应力达到岩石的屈服应力时，扩容和非线性应变开始。此外，随应力水平的增加，扩容和非线性变形呈幂函数形式增加。
Casing is heated by steam in thermal recovery Wells. There are thermal stresses in casing. Casing deforms when stresses exceed yield point.
计算表明，注蒸汽稠油井如果用常规方法固井，在通常的注汽温度下，套管都因热应力而产生屈服变形。
If the design is based on the strain hardened properties, the allowable design stress will usually be above the actual yield point of the HAZ.
如该设计基于应变硬化性能，设计应力通常在HAZ实际屈服点以上。
The conventional photoelastic modes and procedures suffice to indicate whether or not the yield point of the material of the prototype will be exceeded.
常用的光弹性模型和方法能够指明原型材料的屈服点是否将被超过。
Theoretical research based on the quasi-static test, organized loading-displacement hysteretic curves, found out timber frame's approximate yield point;
此外又在试验基础上进行了理论研究，根据试验数据整理出木构架的荷载位移滞回曲线，找出了木构架的近似屈服点；
We introduced a structure equation with macroscopic parameters, which can explain both the yield point phenomenon and strain-ageing of low carbon steels.
我们提出一种新的来自于宏观量构成的理论，将低碳钢的屈服及时效现象统一于同一个理论之下。
The chemical components and microstructure are analyzed for the hot-rolled reinforced bar, of which the yield point is not so clear, some measures proposed.
对存在屈服点不明显问题的热轧带肋钢筋的化学成分和组织进行了分析，提出了改进措施。
An experimental and theoretical study of the earthquake mitigation effect of hysteretic dampers using ultra low yield point steel was presented in this paper.
本文通过试验研究和理论分析探讨极低屈服点软钢阻尼器的减震效果。
The main factors effecting on reliability of bolted joints, the conditions of increasing the reliability of tightening method up to the yield point, and the sc...
文中还提出了影响螺栓连接可靠性的主要因素以及提高屈服点拧紧法可靠度的条件与使用范围。
High strength plate also known as high strength plate, low alloy high strength plate, high strength welding plate. It is characterized by high strength and high yield point.
高强板又称高强度板，低合金高强板，高强度焊接板。主要特点是强度大，屈服点高。
With the application of technology of earthquake resistant energy dissipation(ERED) for skyscrapers, low yield point(LYP)steel used to the fabrication of energy dissipation damper is in focus.
通过合理的成分设计及轧制工艺，宝钢研制出可用于制作耗能阻尼器的系列低屈服强度钢，并成功实现了批量生产和工程应用。
应用推荐