• 采用锻件

    The thick wall by forging.

    youdao

  • 架子设计聚乙烯塑料材质的加立柱保持最大稳定性的地板。

    Stands are constructed of durable thick-wall, polyethylene plastic with a structurally reinforced post and fillable base for maximum stability.

    youdao

  • 有些决定销轴直径可能取决于科学计算科学的部分设计仍然是首要的。

    Some decisions, such as wall thickness and pin diameter, may depend on scientific calculations, but the nonscientific component of design remains primary.

    youdao

  • 以下瘤胃内最多的是拟杆菌、厚壁菌门、螺旋体纤维菌门。

    Bacteroidertes, Firmicutes, Spirochaetes, and Fibrobacteres were the most abundant in rumen under phyla level.

    youdao

  • 最大的问题如何找到合适果酱罐子:如果买新的,也许还不如直接便宜的果酱划算。

    The hardest thing is getting hold of proper thick-walled jam jars; new, they can be more expensive than some cheap jams.

    youdao

  • 燃料开始融化一段时间里热量可能融化四到八英寸的反应堆的容器钢

    Hours after the fuel rods started to melt, the heat.

    youdao

  • 研究者证明动脉中风危险的增加关联,这种检测通常能够发现5%20%的顾客可探测血小板增加

    Researchers have shown that a thickening of artery walls is associated with elevated stroke risk, and such scans typically find that anywhere from 5 to 20 percent of clients have detectable plaque.

    youdao

  • 高度密封,用钢铁混凝土制成非常障。

    The containment structure is a hermetically (air tight) sealed, very thick structure made of steel and concrete.

    youdao

  • 休眠细胞藻菌纲孢子接合子中明显的几常常看见的。

    Distinct layers are often visible in thick-walled resting cells such as chlamydospores or zygotes of phycomycetes.

    youdao

  • 不要低于45摄氏度否则不会留下足够的

    Don't go much below 45 degrees or you will not leave enough wall thickness.

    youdao

  • 这些计算最小必需可能使用作为认可弯头标准

    The minimum wall required by these calculations may be used as the acceptance criteria for bends.

    youdao

  • 首先进行强度稳定性计算主要进行筒体端盖计算、水压试验应力校核以及叶轮的强度校核

    First of all, for strength and stability, mainly a cylinder, cover the wall, the water pressure check and impeller stress test, the axis of strength checking.

    youdao

  • 整个厚壁圆筒达到屈服状态时,推导在内压力轴向联合作用下圆筒塑性极限载荷表达式。

    The relative formulations between limit loads (both axial force and internal pressure ) acting on it are derived while the whole thick-walled tube is led to the yielded state.

    youdao

  • 通过已有文献的比较得出的结论同时适用内层厚壁管的情况

    The conclusions are applicable to the case where the inner tube is thin-walled or thick-walled in comparison with available literatures.

    youdao

  • 较大直径使得强度指数性增加增加只是线性地增加强度。

    Making the diameter larger increases strength exponentially, while increasing the wall thickness only increases the strength linearly.

    youdao

  • 最后分别分析了材料性质截面长宽比、管长最终变形模式影响

    Moreover, the influences of material property, section properties, tube length and thickness to ultimate deformation modes are studied respectively.

    youdao

  • 表层是百叶窗保护作用的裂缝这些都能突出建筑主题

    The blind facade, the protective thick wall, and the slight crevices, all these above reinforce the architectural theme.

    youdao

  • 提出精度概念极其控制方法具有普遍性对于其它制造工艺具有参考作用。

    The introduction of the concept of bellows wall thickness accuracy has the universal significance and reference value for manufacturing technology of other thin wall tube like products.

    youdao

  • 螺纹尺寸规格说明最小爆裂压力材料分类以及规定标记标识要求等。

    Thread dimensional specifications, minimum wall thickness and burst pressure, material classification, and requirements for marking identification were stipulated.

    youdao

  • 认为模具加上真空泵提供压力使结构更好也能更好的控制

    I believe molding two halves with a vacuum pump to provide pressure will produce a better structure and allow me to better control wall thickness.

    youdao

  • 天盖双层

    The canopy walls are of double thickness.

    youdao

  • 塑料水槽设计内容包括制品的材料选择确定,收缩率的确定以及UG软件绘制的过程。

    The flume's design includes the selection of the material, thickness, contractibility and how to use UG to plot it.

    youdao

  • 他们知道黑暗

    They dont know that I am inside this thick wall of darkness.

    youdao

  • 探讨了影响注射成型厚壁塑料制品收缩变形一些因素,提出了对实际生产有指导作用的建议

    Several factors affecting on contraction deformation of thick section injection moulding articles were investigated. Some practical proposals were given.

    youdao

  • 提出采用磁通相结合方法检测在用油管剩余的方法。

    A measuring method combining main magnetic flux and magnetic flux leakage for approaching the residual wall thickness of the oil well tubing in-service was presented.

    youdao

  • 车缝-通过弹()一个贫穷想法

    Sewn-through shells (zero wall thickness) are a poor idea.

    youdao

  • 工厂检验偏移以及频率

    What is the foundry's checking frequency for control of core shift and wall thickness?

    youdao

  • 工厂检验偏移以及频率

    What is the foundry's checking frequency for control of core shift and wall thickness?

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定