矿灯的控制电路部分线路简单、造价低廉。
The section of controlling circuits has simple and low cost.
模拟电路部分分别对放大和滤波进行了设计和开发。
In the part of analog circuit designing, the paper designed and developed amplifier and filter circuit.
该拖体电路部分的主要特点在文章中也有详尽的介绍。
A minute description of the main attributes of the body in electronics is also given.
实现了基于用户环路业务综合的复用的硬件电路部分。
The hardware circuits that are based on subscriber loop integrated service multiplex are also achieved.
经电气信号供应焊盘将电气信号供给到驱动电路部分。
When the electric signal is supplied to the driver circuit part, it is supplied via an electric signal supply pad.
论文着重完成系统的软件控制程序和硬件电路部分设计。
The thesis mainly completes the design of software and parts of hardware.
搭建测试电光采样系统原型，包括光路部分和电路部分。
The prototype of the EOS system, including the optical part and the electrical part is constructed.
电气信号从电气供应盘供给到驱动电路部分中的不同区域。
The electric signal supplied to the electric signal supply pad is branched therefrom and supplied to different areas in the driver circuit part.
本文介绍了核磁共振的原理及小型核磁共振系统电路部分的设计。
This text introduce the theory of nuclear magnetic resonance and the design of a NMR system.
电子式灯座，需除去里面电路部分，重新布线，布线原理图如下。
Electronic type lamp holder, need to remove the circuit part, rewiring, wiring principle scheme as follows.
通过设计实验装置的电路部分，实现对信号的采集、计数和比对。
Through the design of the circuit of the experimental system, the signal was collected, counted and contrasted.
本文介绍了核磁共振的原理及小型核磁共振系统电路部分的设计。
With a view to this, a digital receiver for nuclear magnetic resonance.
电路部分通过机器运作时触碰行程控制开关来实现电机的正反转。
The circuit potion achieves the positive inversion of the motor through touching a stroke control switch when the drinking bottle shredder is running.
控制系统的硬件电路部分主要包括控制器、传感器和电机驱动芯片。
Hardware circuit part of control system mainly includes controller, sensor, and motor driver chip.
该系统由光学部分，电路部分，数据采集部分及数据处理部分组成。
The system is composed by optics part, electronic part, data acquisition part and data processing part.
该模块包括接口部分和功能电路部分，能够完成1路采集和4路回放。
The module includes interface part and function part. It can accomplish 1 channel data acquisition and 4 channels return.
由于现有工艺的限制，因此本课题在实际设计中主要对电路部分进行集成设计。
Owing to the restriction of technologic, this article primary dose the part of circuit integration design, then integrate the all parts on the silicon.
电路部分使用了这种方法最初用于在加速度计，它部署在车辆的安全气囊在撞车时。
Circuitry parts made using this method were initially used in accelerometers, which deployed airbags in vehicles at the time of a crash.
彩色电视机在待机状态，电源供电电路部分和MCU电路部分都会产生待机功耗。
When the color television is in the stand-by mode, the power supply circuit and MCU circuit will still on the power consuming circumstances.
系统硬件的模拟电路部分设计了四电极传感器前置模拟电路以及热敏电阻测温电路；
The analog circuit of the system in this thesis is composed with pre-positive circuit of 4-probe electrode sensor and temperature-measure circuit.
本文对于变换器功率电路部分进行了小信号建模和分析，给出了小信号特性传递函数。
In this thesis the small signal model of the power stage of the converter was established and analyzed, the relative transfer functions were presented.
一种铁路专用联锁式电动脱轨器，由脱轨部分、转辙部分、电路部分以及固定架组成。
Disclosed is a special interlocking electric derail for railway which comprises a derailing portion, a switching portion, a circuit portion and a fixing frame.
该系统的电路部分已成功地应用于J校教务处各种表格的处理，误码率在0.2%以下。
The circuits part of the system is applied to processing various tables of the Dean's Office of J University successfully, the bit error rate is less than 0.2%.
如果输出电压小于预定的电压电平，则开关电路部分将增强的控制信号传输到调节电路。
If the output voltage is less than the predetermined voltage level, the switching circuit portion transmits an enhanced control signal to the regulation circuit.
本文对该仪器的工作原理、机械结构、电路部分设计、数据处理与软件设计也进行了阐述。
This article also represents the operating principle, mechanical principle, circuit design, data procession and software design of such tester.
为了从根本上防止刷卡出错，在非接触ic卡读卡器硬件设计上加入红外发射接收电路部分。
To prevent the mistakes of operating ICC, infrared transmit-receive circuit is added in the contactless ICC reader design now.
在硬件电路部分，根据课题的具体要求，对一些主要芯片进行了选择，然后设计了硬件线路。
At the part of the hardware circuit, according to the concrete commands of the thesis, the main chips of the circuit have been selected and the hardware connecting has been completed.
该仪器的电路部分采用了线阵CCD进行光谱数据采集，采用USB接口进行通讯和系统供电。
The circuit of spectrometer used CCD for spectrum data collection, and used USB interface for communication and system's power.
介绍了显微镜的设计和结构，所用声学聚焦系统、换能器及显微镜的机械微波和电路部分。
The design and construction of the microscope, the acoustic transducer-focusing system, the mechanical microwave and electronic systems are presented.
介绍了显微镜的设计和结构，所用声学聚焦系统、换能器及显微镜的机械微波和电路部分。
The design and construction of the microscope, the acoustic transducer-focusing system, the mechanical microwave and electronic systems are presented.
应用推荐