This paper also discusses the method of adhesive bonding and the reaction mechanism.
并对胶接方法和反应机理进行探讨。
Flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process.
在包装过程中最好使用柔性环氧黏合或软黏胶性结合。
The process of FPC mount is fixing the components to FPC, by means of adhesive bonding, welding, etc.
FPC贴装过程就是通过胶剂黏合或焊接等方法，将元器件固定到FPC上的过程。
In adhesive bonding repair using composite patches, the size of patch has an obvious influence on bonding strength.
在复合材料胶接修补中，补片的尺寸对胶接强度的影响非常关键。
The applications of cryogenic adhesive bonding technology in SQUID non - magnetic Dewar and other fields are introduced.
介绍了低温粘接技术在SQUID 无磁杜瓦及其它领域中的应用。
Micro adhesive bonding technology shows great potential in the assembly of micro-electro-mechanical system (MEMS) products.
微胶接技术非常适用于微机电系统产品的自动化装配过程。
UV-curable adhesive is a class of important material that could be rapidly created adhesive bonding properties by the UV radiation.
紫外光固化胶粘剂是指借助UV辐射使粘接材料快速产生粘接性能的一类胶粘剂。
The failure form of joint, mechanical analysis of joint, joint design and test methods of adhesive bonding of composites are presented briefly in this paper.
本文简略叙述复合材料胶接的接头破坏形式，接头力学分析，接头设计及测试方法。
Sometimes one fabric is backed with another by bonding, either with adhesive, or with thermoplastic fibers which, when heated, fuse the two fabrics together.
有时一种织物，反面用另一种织物粘合在一起，或者用粘性的纤维，或者用热塑性纤维，把两种织物加热粘合在一起。
The bonding strength of the new adhesive completely meets the requirements of orthodontic adhesives.
这种新型粘合剂的粘接强度完全满足了正畸粘合剂的要求。
The synthesis of 2,3- DCB /MMA Copolymer and preparation of the adhesive for bonding rubber to metal with the copolymer above as the main material are introduced.
介绍2，3-二氯丁二烯一甲基丙烯酸甲酯共聚物的合成，以及以该共聚物为主体材料的橡胶同金属热硫化粘结的胶粘剂。
Three typical manifestations of wafer bonding strength were introduced as tensile strength, shear strength and adhesive strength.
介绍了三种典型的圆片键合强度表现形式：抗拉强度、剪切强度和粘接强度。
The recipe and preparation of adhesive R-4 for bonding of rubber and metal was introduced.
介绍了橡胶与金属粘合用胶粘剂R-4的配方和制备方法。
The formulation, physical properties and bonding strength of Adhesive DK-2 are described in this per.
本文叙述了DK-2抗磨胶粘剂的配方、物理性能和粘接强度。
This article introduced the reprocess of polyamide hot melt adhesive for bonding lining cloth of clothing.
具体介绍了服装粘合衬布用聚酰胺热熔胶的后加工。
Selection of adhesive for bonding strength fi eld pull-out tests of thermal insulation layer and substrate was introduced.
介绍了在保温板材与基层的粘结强度现场拉拔试验中粘结剂的选用。
The transmittance of smoke signal at high temperature and the bonding and technical properties of the adhesive were tested.
测试了该胶粘剂试样在高温状态下产生的烟雾信号的透过率以及常温粘接强度和工艺性能。
The experiment results show that the properties of solubility, bonding strength and chemical stability of SE-8 Adhesive are all good enough.
试验结果表明，SE—8胶粘剂的溶解度、粘接强度、化学稳定性等性能良好。
Results showed that the high temperature adhesive cured at room temperature had satisfied bonding performance for graphite materials.
结果表明，室温固化型高温粘结剂对石墨材料具有良好的粘接性能。
Detal adhesive materials used in dental therapy and prosthesis can be divided into three groups, cements, synthetic bonding agents and composite resins.
牙科治疗和修复应用的粘结性材料包括粘固剂、合成粘结剂和复合树脂三大类。
The results show that there have higher peel strength between adhesive tape and polyester or polyamide. It is applicable for bonding the end of zipper cloth base.
实验结果表明，尼龙热熔胶与涤纶或尼龙布基有良好的剥离强度，可应用于拉链布基末端的粘。
Bonding force of substrate and adhesive layer is large. No adhesive failure occurs during storage and construction.
基材与胶层结合力大，在存放或施工过程中不存在脱胶现象。
A contact adhesive for permanent or temporary bonding of most surfaces.
一种接触式粘着剂，用于大部分表面的暂时或永久性粘贴。
Through an analysis of experimental result, we have discussed the bonding mechanism of the adhesive, and the influencing factors of bonding intensity.
通过对实验结果的分析，探讨了胶粘剂的粘合机理以及影响粘接强度的各种因素。
According to the characteristics and requirements of the adhesive joint, the authors design and set up the testing platform of bonding strength for different materials.
根据粘接接头的特点和需要，自行设计和制造了异种材料粘接强度测试平台。
The influences of surface treatments, the pressures during bonding process and the thickness of adhesive layer on shearing strength were investigated with epoxy resin-DDS curing system as adhesive.
采用环氧树脂-DDS固化体系作为胶接剂，探讨了各种金属表面处理方法、胶接时对胶接面施加的压力、胶层厚度等因素对胶接剪切强度的影响。
The consumption of polyurethane adhesives in wood industry is increasing gradually for its advantages, such as formaldehyde free, less adhesive spread, high bonding strength and etc.
聚氨酯胶黏剂由于具有无甲醛， 施胶量少，胶接强度高等众多优点，使其在木材工业中的使用量逐步增加。
The bonding strength is ensured by the correct choice of substrate material, surface preparation, adhesive and process parameter.
粘合强度可以通过选择正确的基体材料、表面处理、胶粘剂和工艺参数得以保证。
A new visible light-cured orthodontic adhesive was prepared and its compositions, properties and orthodontic bonding procedures were represented.
介绍了一种新型可见光固化正畸粘合剂的组成、性能及正畸粘接的工艺。
A new visible light-cured orthodontic adhesive was prepared and its compositions, properties and orthodontic bonding procedures were represented.
介绍了一种新型可见光固化正畸粘合剂的组成、性能及正畸粘接的工艺。
应用推荐