检查高/低速轴向推力轴承浮动许可。
在工作是可以反轴向推力传递至整个管道。
采用圆锥滚子轴承取代现有的轴向推力球轴承。
The tapered roller bearing replaces axial thrust ball bearing.
因为斜齿轮的齿有个角度，所以，在其啮合时就会产生轴向推力。
Because of the Angle of the teeth on helical gears they create a thrust load on the gear when they mesh.
对双螺杆磨浆机的螺杆扭矩、轴向推力和机筒压力进行了测量实验研究。
Metrical experimental studies on screw torque, axial thrust, barrel inwall pressure of twin screw pulping extruder (TSPE) were done.
轴向推力和功耗是影响双螺杆磨浆机可靠性的重要因素，目前尚无理论计算方法。
The axial force and power consumption are important factors of affecting reliability of twin screw pulping extruder, at present there are no theory calculation methods about them.
在泵顶部应该配置排斥叶片，用于排出固体颗粒，减少轴向推力和密封区域的压力。
Repelling vanes shall be provided on the top shroud to expel solids and reduce axial thrust and pressure at the seal area.
在保持轴向推力几乎不变的情况下，选用冲动式叶片保证了叶片有较好的通流能力。
Using of impulse section blade ensured its flow capacity with the axial thrust almost unchanged.
建立了叶轮间隙和迷宫密封的整体模型，并充分考虑了叶轮两侧密封对轴向推力的影响。
Whole model of impeller clearance and labyrinth seal are built up, and the effect of seals with two sides of impeller to axial thrust is considered fully.
MSH系列产品作为针对高压应用的设计，轴向推力通过平衡室系统和圆盘一起进行平衡。
The MSH range is designed for high pressure applications and the axial thrust is balanced by the combination of the drum and disc.
计算高压离心式水泵、压缩机转子流体轴向推力时，需要计算叶轮侧隙中流体压强的分布。
It's necessary to calculate the pressure distribution in the space between. the centrifugal impeller and the case for calculating the axial thrust of high pressure centrifugal pumps and compressures.
具体阐述提高工业汽轮机能力需考虑的主要技术问题：蒸汽流量，转子强度，轴向推力及辅助设施。
This paper presents the key technical points in increasing the capacity of an industrial turbine, such as steam flow, rotor strength, axial thrust and auxiliary equipments.
钢丝绳向新的一层过渡时，对端侧板产生轴向推力，导致侧板弯曲，同时在侧板与筒壁过渡处产生较大应力。
The axial force toward the side board is always produced when the wire rope reaches the new layer. It makes the side board bended and causes very large stress between the side board and the roller.
经济性好：由于G800螺杆泵专用减速机，其输出结构已设计了承受螺杆泵工作时的轴向推力，所以可以减少泵类的轴承座部件，不仅省成本而且结构又可靠合理。
Economy: because of the special design of the G800 mechanical reducer with screw pump, the bearing housing parts can be reduced. Thus, the cost is reduced and the structure is more reliable.
讨论了各种因素对轴向水推力的影响，包括各项推力系数的选取和修正。
Screw propeller theory is then used to calculate the axial thrust and to analyze factors that influence the thrust.
由于增加了一套轴向止推轴承，所有的推力和向心轴承均被分别预加载。
With an additional axial thrust bearing, both the thrust and radial bearings are preloaded individually.
除此之外，具有曲线型齿线之齿轮在运转时亦不会产生轴向的推力。
Moreover, a gear pair with curvilinear - tooth traces operates without axial thrust force.
转子磁场中心安装偏差所产生的轴向磁拉力很小，转子磁极中心挂装高程差所产生的不平衡力偶不致增大推力瓦受力。
The couple of force created by rotor pole center suspending difference may not increase the pressure on the thrust pad.
单向和双向推力角接触球轴承（图1.50和1.51）都用机床主轴轴向刚性作为指导。
Single-direction and double-direction angular contact thrust ball bearings (Figures 1.50 and 1.51) are used for machine tool spindles requiring rigid axial guidance.
这些轴承有特别高的轴向负荷能力，主要用作轧钢机里的推力轴承。
These bearings have a particularly high axial load carrying capacity and are used primarily as thrust bearings in rolling mill applications.
实践证明，堵平衡孔是解决转子轴向负推力问题的一种行之有效的方法。
Practices demonstrate that blocking balance hole is a effective method to resolve the axial negative thrust of rotor.
通过WVIS -ME45隔振器的轴向弹性变形来传递螺旋桨的推力，有效地控制了船舶推进系统的振动和噪声。
It is efficient to control the vibration and noise of the propulsion system since the thrust is transmitted by axial elastic deformation of WVIS-ME45 vibration isolator.
本文通过有限元法求解用流函数表示的拉普拉斯方程，进而计算轴流式机组的静态轴向水推力。
In this thesis, the Finite Element Method is applied to the solution of the Laplace equation formulated by means of stream function for the calculation of the static hydraulic thrust.
补偿器通过受力构件来承受压力推力，只需固定中间支架，产品只能吸收轴向位移。
The compensator bears the pressure or thrust as long as fixed the mid supporting frame and it can only absorb axial displacement.
针对600MW机组启动过程中推力瓦温度高及轴向位移范围超常的问题，从形成原理及现场安装两方面加以分析，并提出处理策略。
This paper aims at the high thrust pad temperature and abnormal axial displacement problem during the start-up course of 600 MW Supercritical Units.
推力球轴承是专为支持轴向力设计的，他们用于轴向力过高，可以由径向轴承传播(的地方)。
Thrust ball bearings are designed for supporting axial forces; they are employed where axial forces are too high to be transmitted by radial bearings.
FAG轴承中的交叉滚子轴承，能同时承受来自各方向荷重（如轴向、推力或动量荷重等）。
The alternate roller bearing in FAG bearing, can bear at the same time come from each direction loading like axial, thrust or momentum loading.
通过计算，分析了3号汽轮机轴向负推力产生的主要原因，介绍了堵平衡孔消除轴向负推力的方法。
This article analysis the major reasons that lead an axial negative thrust in unit 3, introduce the method of remove axial negative thrust with block the balance hole.
轴承采用了单列向心推力球轴承，这种轴承具有同时承受较大的轴向荷载和径向荷载的能力。
Bearing a single row thrust ball bearings to the heart, which has at the same time to bear a greater bearing axial load and radial load capacity.
组合式滚针轴承是由一个向心滚针轴承和一个推力轴承相结合，因此能够承受径向和轴向负荷。
Combined needle roller bearings consist of a radial needle roller bearing combined with a thrust bearing and are consequently able to take up both radial and axial loads.
应用推荐