The object of this dissertation is to calculate the height of screw mandrils from CAD data and develop a mechanical hand to adjust screw mandrils' height automatically.
本文主要介绍根据CAD造型数据计算上下模冲压顶杆的高度，并开发一台顶杆高度自动调节机械手调节离散型面模具顶杆高度。
We can adjust the levelness of the machine by means of shim and screw jack.
我们可以利用垫铁和螺丝千斤顶来调整机器的水平度。
Cup head screws, When should adjust the handwheel on the frame, the first to loosen the screw so that fixed the handwheel.
杯头螺丝；当要调节手轮在机架上的位置时，先要松开此螺丝，以便固定手轮。
Electrically activities;. When should adjust pulling the area is pulling the machine to loosen the screw, casters activities.
活动脚轮；当要调节拉网机拉网的面积时先要松开活动脚轮，螺丝。
Then use the same screw to adjust for a smooth transition from idle to full throttle.
然后使用低速油针调整从怠速到全速引擎都能平顺运转。
Install the base on the ground, and adjust even using the level. Fix the screw, and connect the base and ground.
将底座安装在已打好的基础上，并用水平仪调平。拧好地脚螺栓上的螺母，将底座与基础固定联接。
Add fine adjust device for the pressure of foot, without dial on the adjustable screw, more convenience for operation.
压脚压力采用微调装置，压力调节螺钉设有刻度，更加方便操作。
Also let us adjust the size or pitch of the screw propeller, then try to get high-speed running.
也让我们调整大小或摊位的螺旋桨，然后尝试获得高速运行。
To adjust the setting of the valve, loosen locking cap screw with hex wrench, see Figure 3.
如果要调节阀门的设置，则利用六角扳手松开锁紧帽螺丝，参阅图3。
Remove the throat plate, loosen hook screw 6 and adjust the hook.
调整旋梭时，请卸下针板，拧松旋梭固定螺丝6，然后进行调整。
Adjusting screw for outlet gas pressure is set on reducer; it can adjust working pressure for requirements.
减压器上设有出气压力调整螺钉，通过调整出气压力螺钉来调节喷气阀所需求的工作压力。
Loose soleplate screw of the roller shelf, and adjust the central height of the two rollers by increasing or decreasing cushion, then tighten the screw.
松开罗架的底板螺丝，用增垫和去垫的方法调整两罗拉的中心高度，然后再拧紧螺丝。
Before the rollers and adjust to screw so that the roll from the direction and avoid refined rubber machine increases the damage of the frame rollers or act as a security role.
前辊筒便向调整螺杆方向移动，使辊距增大而避免炼胶机辊筒或机架的损坏，起到安全的作用。
Twin adjust rotation screw on both covers and pistons, to avoid continuous heavy stresses by teeth, shaft, body.
调整旋转双螺杆都涵盖和活塞队，以避免连续沉重压力的牙齿，竖井机构。
Different from traditional electric and pneumatic screwdriver tools, this screwdriver system can adjust the screw with no axial pressure when driving screws.
区别于现有的电动、气动螺丝刀工具，该螺丝刀系统在驱动螺丝时，能对螺钉头实现无轴向压力的调节。
The position of the external sleeve can be adjusted by a screw (3) and a nut (4) to adjust the size of the gap.
通过螺丝（3）和螺母（4）可以调节外套位置，以调节间隙的大小。
But loss of correction and screw loosening often occurs in patients with osteoporosis, or screw has less stability in revision surgery and re-adjust of screw position.
但骨质疏松患者容易出现螺钉松动和复位矫正丢失、螺钉翻修或者重新调整螺钉位置后螺钉的稳定性较差。
Special adjustment screw is currently widely applied in auto lights, and functions to adjust the actuation device;
特殊调节螺丝目前主要应用于汽车灯上、起调节传动的功能；
Turning adjustment screw to change the height of the trap door open in order to adjust the volume of high-pressure gas through the pressure to achieve the required value.
转动调节螺杆，改变活门开启的高度，从而调节高压气体的通过量并达到所需的压力值。
For the standard 1g design, this was quite an easy adjustment to make, you only had to adjust a single screw.
对于标准的1g设计，这相当是壹个容易的调整制造，你才必需调整一个螺丝钉。
Adjust it and screw down all the screws.
给予调整。拧紧所有螺钉。
The Central Line of the positioning screw bolt and an outlet shaft lever are coherent basically in order to adjust the front and back position of the outlet shaft lever.
定位螺杆与出轴杆两者的中心线基本一致，用以调整出轴杆前后位置。
AX-100L Slab Thickness Machine is adopted gantry linkage structure, autofeed driven by trolly screw mandrel and America EMERSON transducer to adjust the speed steplessly.
AX-100L大板定厚机采用龙门式连体结构，台车丝杆驱动自动走刀，并采用美国爱默生变频器可进行无极高速。
AX-100L Slab Thickness Machine is adopted gantry linkage structure, autofeed driven by trolly screw mandrel and America EMERSON transducer to adjust the speed steplessly.
AX-100L大板定厚机采用龙门式连体结构，台车丝杆驱动自动走刀，并采用美国爱默生变频器可进行无极高速。
应用推荐