Now air injection into light oil for EOR has received more attention.
目前注空气提高轻质原油采收率受到广泛的关注。
Air injection is a promising and proven technology as for EOR process.
注空气提高原油采收率是一种很有前景的开发技术。
Lastly, catalyzing conversion regular combining with the secondary-air injection system is analyzed by test.
第三部分对增加了二次空气的催化转化规律进行了实验分析。
Objective to study the effects of facial support in prone position for patients after vitrectomy with air injection.
目的探讨应用俯卧位面部支架对玻璃体切除联合气体填充术后患者临床护理效果的影响。
With the increase of reservoir temperature, displacement efficient increase of flue gas injection is more than of air injection.
注空气、烟道气的驱油效率随着温度的升高而上升，但空气的升幅较大。
The study on air injection mainly aims at the heavy oil in China, but most of low permeability reservoirs are light oil reservoirs.
低渗透油藏大多属于轻质油藏，轻质油藏注空气已经越来越受到人们的关注。
Light oil reservoir air injection technology is used popularly in overseas, which played the role in enhancing the oil recovery ratio.
轻质油藏注空气技术在国外较为广泛的运用，而且切实起到了提高采收率的作用。
It should be noted that air injection was successful in this application because the bitumen was first preheated and mobilized with steam.
这表明注空气是成功的，因为沥青质首先被预热并且随蒸汽移动。
However, air injection technology has not been widely used in China so long, mainly due to the application of the technology still exists many problems.
但注空气技术在我国一直没有大规模的应用，这主要是因为目前该技术的应用还存在诸多问题。
In this paper, the experimental investigation and theoretical study on reduction of the ducted propeller cavitation noise by air injection are presented.
本文介绍用人工喷入空气的方法降低导管螺旋浆空泡噪声的试验和理论研究。
The American field and the experimental materials indicate that it can enhance the EOR above 6% by adopting the air injection technology after water flooding.
美国现场和实验资料表明，注水后采取注空气采油可提高油藏采收率6%以上。
The advancing velocity of combustion front is proportional to air injection rate. The air injection rate has no significant effect on oil recovery and air consumption.
燃烧前缘的推进速度与空气注入速率成正比，而提高空气注入速率对采收率和空气消耗量没有太大的影响。
Objective to investigate the effect of air injection to the anterior chamber treating shallow anterior chamber after trabeculectomy in primary Angle closure glaucoma (PACG).
目的探讨应用前房注气术治疗原发性闭角型青光眼小梁切除术后浅前房的效果。
To illustrate this method feasibility to reduction the smoke emission, the air injection system developed was applied to the naturally aspirated engine experimental station.
为了研究电动增压补气系统对于柴油机加速补气减少碳烟排放这一方法的可行性，将研制的电动增压补气系统应用到试验台架中去。
Analysis showed that: inlet air injection technical solutions were adopted more easily without the need for damage of the turbocharger structure; it's more suitable for buses.
分析表明：进气道补气的技术方案改装方便，无需破坏涡轮增压器结构，更适合于公交车使用。
It may effectively reduce the HC emissions to use a catalyst with low light-off temperature, close-coupled catalyst, HC traps, second air injection and electrically heated catalyst.
采用如低起燃温度催化剂、密耦催化剂、HC捕集器、二次空气注入和电加热催化剂等在内的排气后处理技术，可以有效地减少污染物尤其是HC的排放。
Results of the experiment show that the air injection has a distinct effect on fiber fractionation, and a good fractionation performance is obtained with increasing the air injection.
实验结果表明，气体的充入对纤维筛分有明显的影响，随着充气量的增加筛分效果将得到改善。
Compositions of the test bench were introduced; the basic design of air injection system and its transient measurement and control system to meet the test requirements were described.
文中介绍了试验台架组成，阐述了试验补气系统及满足瞬态试验要求的补气测控系统的基本设计思想。
The Three-Dimension-Laser Particle Dynamic Analyzer (PDA) was utilized to conduct experimental investigation of the turbulent combustion in a swirl combustor with staged air injection.
本文应用三维激光粒子动态分析仪（PDA）对分级进风旋流燃烧室内的湍流燃烧过程进行了实验测量。
At last, this paper evaluates some parameters which may have influence on recovery of air injection, reservoir temperature, injecting rate, water saturation, permeability and grid size.
最后通过数值模拟评价了一些影响注空气采收率的参数，油藏温度、注入速度、含水饱和度、渗透率和模型网格大小。
The rate of combustion reaction and liquid production are increased with the increase of frequency factor of combustion, decrease of activity energy, and increase of air injection rate.
增加燃烧反应的频率因子、降低活化能、增大注气速度，会加快燃烧反应，增加产液量；
This paper gives an introduction on indoor testing, numerical simulation, field application and pilot test design of air injection, and discusses its effectiveness in enhancing oil rec...
本文介绍有关注空气的室内试验、数值模拟及现场应用与先导试验设计，同时探讨这种工艺方法在提高采收率方面的效果。
Conclusion: the reduction rate using the air injection at intervals is obviously higher than that with the usual method and the shorter the intussusception time the higher the reduction rate.
结论：采用间歇注气法整复肠套叠比一般注气法复位率高，并且肠套叠时间越短复位率越高。
Secondly, the diesel engine steady and transient experiments for air injection were made respectively, the test conditions of which were determined according to the data of the Wuhan bus road test.
其次，本文根据武汉市公交车道路试验采集的路谱数据研究成果确定试验工况，分别对柴油机进行稳态及瞬态补气试验。
To explore, simple, safe and effective way of treating retinal detachment due to macular break 48 cases of macular breaking retinal detachment were treated by laser with intravitreous air injection.
为寻求一种简便、安全、有效的治疗黄斑裂孔视网膜脱离的方法，本组收治黄斑裂孔视网膜脱离48例。
To reduce emissions in existing combustors, fuel is premixed with a large amount of swirling air flow prior to injection into the combustor.
现行的燃烧室要想减少排放量，必须在燃料注入燃烧室之前就通过大量的空气流将燃料混合好。
Summarized some important experience on designing injection mould of plastic air intake manifold.
总结出了在设计塑料进气歧管注塑模具时要注意的几个问题。
The injection molding is an important tache to exploit plastic air intake manifold.
注塑成型工艺是开发塑料进气歧管的重要环节。
The injection molding is an important tache to exploit plastic air intake manifold.
注塑成型工艺是开发塑料进气歧管的重要环节。
应用推荐