The charge injection is modulated by the gate field.
通过所述栅极场来调制电荷注入。
The electric charge injection is necessary to enhance pyroelectric coefficient of composite.
电荷注入机制是制成高的纯熟释电系数复合材料的必需条件。
The improvements are most likely due to the reduction of the gate leakage current and the charge injection effect.
这些效能改进的原因可以归之于经过表面处理后，闸极漏电流的降低以及载子注入的减少。
The experimental results show that not only space charge injection but its detrapping also makes samples breakdown.
结果表明，电介质的击穿并不总是发生在电荷的注入过程中，也可以发生在空间电荷的脱阱过程中。
The sample and hold circuit is employed by the bottom plate sampling technique, which could not only cancel the charge injection error but also eliminate the effect of clock feed-through.
采样保持电路设计采用了电容下极板采样技术，不仅有效地避免了电荷注入效应引起的采样信号失真，而且消除了时钟馈通效应的不良影响。
The CEC technique compensates the sampling bandwidth by eliminating the impact from finite on-resistance of the sampling switch, and avoids increasing clock feedthrough and charge injection.
该技术通过消除采样开关有限导通电阻的影响，补偿了采样带宽，并避免了时钟馈通和电荷注入的加剧。
This invention provides a method for improving the organic charge injection in organic film component, relating to improving the quality of material and belonging to material science region.
本发明改善有机薄膜元器件中有机膜电荷注入的方法涉及对材料性能的改良，属于材料科学领域。
The basic unit structure of the SI is introduced in this paper. It also discusses the main factors which affects the precision of fault diagnosis and analyzes the charge injection error in detail.
介绍了开关电流电路的基本单元结构，讨论了影响故障诊断精度的主要因素，重点分析了电荷注入误差。
An improved structure of switched-capacitor integrator is used to reduce the harmonic distortion induced by charge-injection effect.
通过改进积分器的结构，显著减小了开关电荷注入效应引起的调制器的谐波失真。
Charge to breakdown of the thin gate oxides was tested and investigated by controlling the amounts of injected hot electrons and holes separately with substrate hot holes injection method.
利用衬底热空穴注入技术分别控制注入到薄栅氧化层中的热电子和空穴量，对相关击穿电荷进行了测试和研究。
The improvement of tandem device performance is attributed to the efficient electron and hole injection from charge generation layer to two adjacent emission units.
叠层发光器件性能的提高与中间电荷产生层向上下两个发光单元有效的电子、空穴注入有关。
Water injection system for charge gas compressor is introduced in the article and comparison is made for charge gas compressor with water injection and oil injection.
介绍了裂解气压缩机注水系统，对压缩机注油与注水进行了比较。
The charge state distribution of the ions passing through the carbon foil has great influence on the performance of the accelerator and thus plays a key role in the charge stripping injection.
在剥离注入中，带电离子通过碳膜后的电荷态分布对注入效率有较大影响。
After using oil injection instead of water, analysis is also given to the actual situations of after-cooler of charge gas compressor and inter-stage tank.
分析了由注油改为注水后，裂解气压缩机后冷器和段间罐的情况。
The design is characterized by short flow, double pot injection, concentrated phase transmission of charge and discharge, advanced and rational control technology.
该设计具有流程短并罐喷吹，上出料浓相输送，控制技术先进合理等特点。
Through tests both in laboratory and production conditions this technology has been proved to be simple in use and valid in transmitting the standard fuel charge of the fuel-injection pump.
经过实验室试验与生产考核，证明该方法简易可行，能达到传递喷油泵标准油量的目的。
This paper developed a technology for transmitting the standard fuel charge of the fuel-injection pump with a floating value.
本文提出了用浮动法传递喷油泵标准油量。
This paper developed a technology for transmitting the standard fuel charge of the fuel-injection pump with a floating value.
本文提出了用浮动法传递喷油泵标准油量。
应用推荐