The cold extrusion process can ensure forming of the cylinder.
该工艺保证了该零件圆柱部冷挤压成形的顺利进行。
An example shows the application of the CAD of cold extrusion die for slot wedge.
并结合一个应用实例来说明槽楔冷挤模cad系统的应用。
The initial design of cold extrusion process and die was obtained by code retrieval.
冷挤压工艺复杂，影响因素多，造成冷挤压工艺设计难度大。
The problem of cold extrusion for inner ratchets of bicycle's flywheel was discussed.
探讨自行车飞壳内棘齿的冷挤压成形问题。
Simulated test method-the method for estimating pressures of cold extrusion is presented.
提出了一种估算冷挤压力的方法一模拟试验法。
There are lots of advantages by cold extrusion for straight knurl nut in a single process.
直纹滚花螺母采用冷挤压一次成形新工艺，成效显著。
The cold extrusion process and mould design have been introduced of the pressing drill sleeve.
介绍了冲钻套筒的冷挤压工艺、模具设计。
This article introduce the applied method of cold extrusion in manufacture beam unit's driving cord.
着重介绍了冷挤压技术在制造抽油机驱动绳中的应用方法。
Such as sheet metal blanking, bending, stretching, fine blanking, the cold extrusion of metal parts.
如板材的冲裁、弯曲、拉伸、精冲、冷挤压金属零件。
This paper introduced the knowledge based system framework of multistage cold extrusion process planning.
介绍了冷挤压工艺规划知识基系统功能的设计。
This paper studies and discusses the forming analysis and forming method of cold extrusion for precision gear.
对精密齿轮的冷挤压成形分析、成形方法进行了概述。
The article introduces the application of twisted steel sleeve cold extrusion technology to construction in detail.
详细介绍了带肋钢筋套管冷挤压技术在施工中的具体应用。
Cold extrusion punch is an important workpiece in punches and its strength analysis is a key component in punch design.
凸模是冷挤压模具中重要的工件，其强度计算是模具设计的一个主要课题。
The simulation results show that the cold extrusion process can greatly save copper materials and reduce production cost.
模拟结果表明，所提出的冷挤压工艺可以极大地节省铜材料，降低生产成本。
This paper mainly performs the design and mechanical analysis and research on cold extrusion mold of the gear axis in cars.
本文主要对汽车用齿轮轴的冷挤压模具进行了设计和力学分析研究。
This equipment is mainly applied to the cold extrusion forming of thin-walled tubes or annealing of metal tube coated curing.
本设备主要适用于经冷挤压成形的薄壁铝管退火或金属管内涂液固化。
The knowledge representation methods and fuzzy reasoning mechanism of a cold extrusion process planning system were researched.
研究了冷挤压工艺设计领域的知识表示以及冷挤压工艺设计系统的模糊推理机制。
Numerical simulation on cold extrusion process of automobile starter socket has been carried out by using the software DEFORM3D.
采用塑性成形有限元分析软件DEFORM3D，对汽车启动器套筒冷挤压齿部成形过程进行了数值模拟。
The forming process, die design and some manufacturing main points in cold extrusion of piston pins are presented in this paper.
介绍了活塞销冷挤压的生产工艺、模具设计及制造特点。
An analysis on the cold extrusion process and a technological experiment were made for the two spline ends of a slim drive shaft.
细长传动轴两端花键头进行了冷挤压加工分析与工艺实验。
The paper expounds the experiment of embryonic form of the curve plate with cold extrusion and the hydraulics function load systems.
文中介绍冷挤压雏形幕墙曲面板的实验和液压加载系统。
Cold extrusion technique of bolt is made a thorough analysis and study Realistic program of the bolt cold extrusion technique is put forward.
对该螺钉的冷挤压工艺进行了深入地研究，从而提出了切实可行的冷挤压工艺。
In this paper, the advantages of the manufacturing on the cutting copper tube joint with the cold extrusion heading technology are pointed out.
文中指出了采用冷挤镦工艺代替切削加工生产铜管接头的优点。
Cold extrusion force is the key of the success of cold extrusion process. The calculation of extrusion force is usually completed by manual work.
冷挤压力的高低是冷挤压工艺成败的关键，通常挤压力计算是人工完成的。
The verification tests of cold extrusion process and fatigue life of a spline shaft show that the analysis results agree well with those of testing.
经花键冷挤压工艺试验和疲劳试验验证，分析结果和试验结果吻合很好。
The working process, structure and control system of a three-dimensional manipulating robot for cold extrusion forming of metal have been introduced.
介绍了用于金属冷挤压成形的三维操作机器人的工作过程、结构与控制系统。
The forming process by cold extrusion for the hood pedestal of the auto air_conditioner compressor and the design of the cold extruding die were introduced.
介绍了车用空调压缩机罩体支架的冷挤压成形工艺及冷挤压模具设计，采用工艺试验的方法确定挤压坯料尺寸。
Form and dimension may also be achieved by a number of alternative processes such as hot or cold extrusion, sand casting, die casting, and precision casting.
形式和尺寸也可以通过其它一些可选工艺来达到，比如热挤出或冷挤出加工，沙模铸造，拉模铸造，或精密铸造。
This paper presents an unified computer model for calculating the com - bined dies for automotive cold extrusion parts with different materials and structure.
介绍了用于汽车零件冷挤压的任意层、不同材料组合模的统一计算模型。
This article introduces an approach for cold extrusion of thin -wall outer -screw and analyses the characteristics of cold extrusion of thin-wall outer-screw.
分析了薄壁厚外螺纹滚压成形的特点，介绍了薄壁厚外螺纹滚压加工方法。
应用推荐