Baosteel's double cold reduction mill is the first DCR line introduced from abroad.
宝钢二次冷轧机组是国内引进的第一条二次冷轧机组。
In China, only Baosteel has ability to produce this product using the double cold reduction (DCR) technology.
目前国内只有宝钢采用二次冷轧(DCR)技术进行生产。
The effect of normalizing temperature on microstructure and texture of non-oriented silicon steel sheets when adopting double cold reduction has been studied.
研究了二次冷轧工艺常化温度对冷轧无取向硅钢薄带组织结构和磁性能的影响。
Process of rolling cold coils of pickled hot-rolled sheet through a cold reduction mill to make the stainless steel stronger, thinner, and smoother by applying pressure.
通过冷轧工厂轧制热轧的、酸洗的不锈钢薄板使不锈钢在压力作用下更薄、强度更高、更光滑。
The Project 956 Sovremenny class destroyer is regarded as outdated in that it is a Cold War-era design with obvious external profile and no radar cross-section reduction features.
现代级956型驱逐舰被认为是一种过时的冷战-时代设计，有明显的外轮廓和没有雷达横截面减少功能。
The reduction partition has effect important in two-time cold rolling on Drawability of IF steel, because reduction has effect in cold rolling on {111} texture.
if钢的冷轧压下率分配对深冲性能有重要的影响，是由于冷轧过程的压下率对(111)织构的形成有影响。
Mechanical properties testing, SEM and TEM was used to study the effects of cold rolled reduction and aging temperature on the cohesion of the weak interface of DISC.
通过力学性能测试、扫描电镜及透射电镜观察，研究了冷轧压下量及时效温度对内生复合钢板弱界面结合强度的影响。
The researchers found that a reduction in ultraviolet (UV) radiation from the sun can affect high-altitude wind patterns in the Northern Hemisphere, triggering cold winters.
研究人员发现，太阳紫外线辐射水准的降低可以影响北半球高纬度的环流形态，导致冷冬。
One key factor of direct reduction of cold bond pellets is the choice of shaped binder.
冷固结球团直接还原工艺成功的关键因素之一是成型粘结剂的选用。
The effects of coiling temperature and cold rolling reduction ratio on deep-drawing properties of low-carbon sheets hot-rolled by FTSR of Tangsteel were investigated in laboratory.
采用唐山钢铁股份有限公司FTSR连铸连轧生产线生产的热轧卷作为生产冷轧低碳钢板的原料，研究了不同卷取温度和冷轧压下率对冷轧薄板深冲性能的影响。
The reduction rule of cold rolled narrow steel strip by usual method, It's rolled energy consumtion isn't the least usually.
按一般方法设计的冷轧窄带钢压下规程，轧制能耗不一定是最小的。
The IC 218 alloy showed different annealing behaviors after cold rolling with varying reduction amount.
IC 2 1 8合金在不同变形量冷轧后，表现出不同的退火行为。
Late response showed ravioli, dim state (or dream-like state), behavior lazy, cold, lethargy, slow, active reduction of the action or language, such as reduction or loss of orientation.
表现为反应迟饨、朦胧状态(或称梦样状态)、行为懒散、冷淡、嗜睡、动作缓慢、主动的动作或语言减少、定向力降低或丧失等。
Iron ores. Low temperature disintegration test. Method using cold tumbling after static reduction.
铁矿石。低温碎解试验。利用静态收缩后的冷滚方法。
Results show that cold pad-batch process can impart the fabric good size removal and capillary effect, but large strength reduction and long cycle.
结果表明，冷轧堆处理的织物退浆率较高，毛效好，但织物强力下降多，且周期长；
The results show that, the cold rolling reduction has a great effect on the development of phase transformation textures.
结果表明冷轧形变量对相变织构的形成影响最大。
The increase of net CO_2 assimilation rate by fruit set after a cold night indicated that feedback inhibition was partially responsible for the reduction of photosynthesis.
低夜温条件下增加果实负载可以提高第二天黄瓜源叶的光合速率，表明反馈抑制是低夜温造成黄瓜第二天光合作用下降的原因之一。
The effects of coiling temperature and cold rolling reduction ratio on deep-drawing properties of low-carbon sheets hot-rolled by FTSR of Tangsteel were investigated in laboratory.
以低碳钢为实验原料，采用不同卷取温度和冷轧压下率进行工业实验，研究了卷取温度和冷轧压下率对深冲板组织和性能的影响。
The mechanical property of the samples with slight banded structure is unnecessarily excellent, the annealing parameters adopted ought to accord with the reduction after cold rolling.
带状组织不明显的材料力学性能未必优越，退火工艺参数的选择应和冷轧压下量合理匹配。
The mechanical property of the samples with slight banded structure is unnecessarily excellent, the annealing parameters adopted ought to accord with the reduction after cold roiling.
带状组织不明显的材料力学性能未必优越，退火工艺参数的选择应和冷轧压下量合理匹配。
The reduction dynamics of carbon containing pellets has been dis-cussed. The measurement of metallurgical properties of the cold bonded pellets was carried out in laboratory.
简述了含碳球团的还原动力学，介绍了含碳冷固结球团的试验室冶金性能测定情况，指出含碳球团只有在较高温度下才具有高速还原的效果。
Reduction of cold welding tendency;
减少冷焊倾向；
During cold drawing, the alloy exhibited excellent workability. Deformation twins appeared when the reduction of cold deformation was around 20%.
当冷变形率在20%左右时，出现变形孪晶，使得合金强度有大幅度提高。
An exemplary embodiment of the invention provides a method for producing an ultra thin wall metallic tube by cold working method with significant wall thickness reduction.
本发明提供一种用冷加工法制造超薄壁金属管的方法。
An exemplary embodiment of the invention provides a method for producing an ultra thin wall metallic tube by cold working method with significant wall thickness reduction.
本发明提供一种用冷加工法制造超薄壁金属管的方法。
应用推荐