Finally, I tested the parsing by checking to see if the object contained a cooling rate multiplier.
最后，通过检查此对象是否包含冷却率乘数测试解析过程。
For maximum softness and ductility the cooling rate should be very slow, such as allowing the parts to cool down with the furnace.
为了得到最大柔软性和延展性冷却速率应该很慢，比如让零件与炉子一起冷下来。
The refined microstructure is insensitive to cooling rate, being independent of casting thickness.
这种合金的细小显微组织对冷却速度不敏感，不因铸件壁厚不同而变化。
The slow heating rate and the rapid cooling rate after sintering are favorable for improving the room temperature mechanical properties.
较慢的加热速率和烧结完成后较快的冷却速率均有利于提高材料的室温力学性能。
The results of measurement show that the cooling rate in vertical ventilation is quicker than lateral ventilation and the cooling uniformity is better too.
实验测试结果表明：垂直送风式具有冷却速度更快、冷却更均匀的特点。
The cooling rate and denudation rate decreased overall from north to south.
总体上自北而南，剥蚀速率和冷却速率均逐渐变小。
The critical cooling rate for the glass formation in the tube was determined.
确定了在落管中形成玻璃的临界冷却速率。
Two methods for reducing cooling rate during underwater wet welding are studied.
研究了两种能应用于水下湿法焊接的缓冷方法。
The other reasons were lower tempering temperature and slower temper cooling rate.
回火温度偏低及回火冷却速度偏缓等，是零件冲击韧度不足的另一原因。
The cooling rate is faster in chromite sand mold, but also causes more porosity in castings.
铬砂制作的砂模可让铸件有较快的冷却速率，但也产生较多的微孔隙。
The atmospheric radiation balance and the net radiation cooling rate in tropo-spheric layers.
对流层内各层大气的辐射差额及其辐射冷却率。
The strength of waxy structure and gelation temperature decreased when increasing cooling rate.
降温速率越高，测量温度下蜡晶结构强度和胶凝温度越低。
When cooling rate increased, the ferrite did not change too much, but the grain sizes decreased.
铁素体随冷却速率的升高变化不大，但晶粒变小。
The condenser behind the refrigerator must keep clean because dust will affect the cooling rate.
柜后的凝结器则要经常清扫，因积在上面的尘埃会妨碍散热。
As a result, It is found that the cooling rate has great effect on the Nb (CN) nucleation and growth.
计算结果表明：冷却速率对碳氮化铌的析出及长大有重要影响。
However, the cooling rate obtained in these tests was very difficult to do under the industrial scale.
然而，实验室条件下试验所达到的冷却速率在工业化生产中较难实现。
In addition, lengthening the cooling time or lowering the cooling rate can reduce the residual stresses.
另外，延长喂料冷却时间或降低喂料的冷却速率有助于减小残余应力。
The Raman spectroscopy measurements indicate that silicate glass structure is insensitive to cooling rate.
拉曼光谱检测显示，硅酸盐玻璃的结构对降温速度变化不敏感。
The results indicate membrane permeability and cooling rate are main factors that affect the cell shrinkage.
计算结果表明，膜的渗透性和冷却速率是影响细胞体积收缩的主要因素。
When the boron content is high and the cooling rate is relatively low, boride can exist at the dendrite arm.
当硼含量较高、冷却速度较慢时，硼化物存在于枝晶干。
The main factors that affect the grain refinement are heating and cooling rate, holding time and cycle index.
影响细化效果的主要因素有：加热速度、保温时间、冷却速度和循环次数。
The maximum thickness of amorphous alloy ribbons can also be determined by this formula and the critical cooling rate.
由这个公式和临界冷却速度还能决定出非晶态合金丝带的最大厚度。
A mathematical model was developed to ensure that the latent heat was dealt with appropriately under high cooling rate.
并进一步建立了快速冷却条件下凝固潜热处理的模型。
The distribution of total cooling rate in the lower atmosphere is mainly determined the distribution of water vapor cooling rate.
大气低层总冷却率的分布主要取决于水汽冷却率的分布。
Applying the method of Lagrange multiplier, the system is optimized for maximum cooling rate and gets the rate general expression.
运用拉格朗日乘数法，以最大制冷量为优化目标，对该系统进行了优化，得到最大制冷量的一般表达式。
The influence of cooling rate after 40 % hot deformation on structure and properties of high carbon chromium cast steel was studied.
研究了经40%热变形后不同冷却速度下高碳铬铸钢的组织和性能。
The processing parameters of PEEK composites include cooling rate, forming pressure, forming temperature and the holding time in melt.
其成型工艺参数包括冷却速度、成型压力、成型温度、保温时间。
The processing parameters of PEEK composites include cooling rate, forming pressure, forming temperature and the holding time in melt.
其成型工艺参数包括冷却速度、成型压力、成型温度、保温时间。
应用推荐