This paper intends to study the influence of rapid cooling time after rolling on the microstructure and mechanical properties of low-carbon steel.
本文研究了轧后快冷时间对控轧低碳钢板组织和力学性能的影响。
Several methods to determine the cooling time of injection molded slabs of crystalline plastics are discussed based on the theory of heat transfer.
从传热学基本原理出发，推导出结晶性平板状注塑制品冷却时间的几种计算方法。
The pre-cooling of fruits and vegetables is an important step in the cold-chain, and a proper pre-cooling time period can assure the quality of fruits and vegetables.
果蔬预冷是冷藏链中一个重要环节，适当的预冷时间能保证果蔬质量。
Short heating or cooling time and stable temperature.
加温及冷却时间快速，温度稳定。
My clients were happy because I was able to reduce cooling time.
我的客户很满意，因为可以降低冷却时间。
Jig for special PET, compelling cooling, shorten the cooling time in the mold.
特殊瓶胚专用治具不伤瓶胚，强制风冷，缩短模内冷却时间。
The packing time, cooling time and packing pressure are the most important factors.
其中保压时间、冷却时间及保压压力是最重要的因子。
The packing time is about 80% of the cooling time which itself is often less than that which is set.
保压时间大约是冷却时间的80%，冷却时间常常小于其设定值。
In addition, lengthening the cooling time or lowering the cooling rate can reduce the residual stresses.
另外，延长喂料冷却时间或降低喂料的冷却速率有助于减小残余应力。
Finally, we make computer simulation for the cooling process and obtain the temperature as a function of the cooling time.
最后对冷却的物理过程进行了理论计算，从而得到了冷却过程中温度随时间的变化曲线。
When the laser scanning speed increases, the laser radiation and cooling time get shorter, so the growing direction of microstructures is changed sharply.
提高激光扫描速率，造成激光辐射和冷却时间变短，合金微观组织生长方向变化显著；
Therefore, the two phase cooling technology is characterized in guaranteed food safety, good meat quality, saved cooling time, low shrinkage loss and remarkable social and economic benefits.
所以两段式冷却具有肉食安全有保障、肉质好、省时间、干损耗小等特点，其社会、经济效益相当可观。
The theoretical prediction values of the surface temperature of heavy rail, the straightening temperature and corresponding cooling time are in reasonable agreement with experimental results.
重轨表面温度、矫前温度及相对应的冷却时间计算值与实测结果基本相符。
The variation of the cooling temperature of the green carbon anode with the cooling time, the temperature of cooling water and the forming temperature has been studied by computing simulation.
通过数学模型描述炭阳极生坯冷却过程，研究炭阳极冷却温度与冷却时间、冷却水温及成型温度间的关系。
Results 64 wet bags are found in 8000 pressure steam sterilization bags. It is due to damp before sterilization, packaging and transport, drying and cooling time, saturation of the steam, and so on.
结果8000个压力蒸气灭菌包裹中发现了64个湿包，与灭菌前包裹受潮、包裹包装和运载、干燥和冷却时间以及蒸气的饱和度等因素相关。
The algorithm of calculating the equivalent distance of the Jominy sample was deduced by making use of the same cooling time in the Hardenability Sensitive Temperature Range as the cooling criterion.
以淬透性敏感区间内的冷却时间相同为冷速判据，得出了直接计算等效端淬距离的算法；
The algorithm of calculating the equivalent distance of the Jominy sample was deduced by making use of the same cooling time in the Hardenability Sensitive Temperature Range as the cooling criterion.
以淬透性敏感区间内的冷却时间相同为冷速判据，得出了直接计算等效端淬距离的算法；
应用推荐