Introduces the basic principle of auxiliary design on axially-symmetric spare part with computer and tells the content of computer software as well as its program method and its stage.
本文介绍了轴对称零件计算机辅助设计的基本原理和计算机软件的内容及软件的设计方法、步骤。
In addition, the hardware designing and the software programming, also the computer realization method, is studied, so the whole complex design process of the computer control system is studied.
另外研究了控制系统的硬件设计和软件编程及采用计算机控制的具体实现方法，较全面说明了复杂计算机控制系统的设计过程。
The deficiencies in current methods of cylinder design are studied and a new method for CAD software development-Computer-Aided-Design with varible structure is presented.
本文分析了目前液压缸设计方法的不足，提出了一种开发CAD软件的新方法——计算机辅助变结构设计方法。
Conclusion: the use of phase measuring profilometry and re software is a convenient and effective method to the computer-aided design for the restoration of unilateral orbital defect.
结论：应用位相测量轮廓术和逆向工程软件进行单侧眼眶部缺损修复的计算机辅助设计是一种切实可行的方法。
A computer automatic testing system of pressure testing machine and the design method of its software were introduced.
介绍了压力试验机的计算机自动测试系统构成及软件设计方法。
This paper elaborates the design method of the lower computer of air quality parameter monitoring system and its software and hardware realization.
本文阐述了空气质量参数的远程监测系统的下位机设计方法及其软硬件的实现过程。
The method to increase reliability of computer monitor and trouble diagnosis system and counter measure of interference in the design of software and hardware are described.
阐述了在软、硬件设计中所采取的提高计算机监测及故障诊断系统可靠性及抗干扰性的方法。
With the increasing complexity of computer software architecture, traditional software analysis and design method has been unable to meet practical needs.
随着计算机软件体系结构的复杂性不断增加，传统的软件分析设计方法已经无法满足实际工程需要。
An intelligently arranged computer method is put forward aimed at the difficulty in the design of water distribution system and a corresponding software is also programmed.
针对注水井配水系统设计中的复杂问题，制定了配水工具智能化排布的计算机算法，并编制了相应的软件。
A method is proposed to design the computer software that is used to assure joint quality of resistant spot welding based on parameters monitoring and information processing.
提出一种基于参数监测和信息处理保证电阻点焊接头质量的计算机软件系统实现方法。
Computer aided design of steering clutch in the bulldozer based on three-dimensional design software MDT was studied in theories. And the realism significance of this method was discussed.
以三维设计软件MDT为平台，对推土机转向离合器的计算机辅助设计系统的构成和功能特点进行研究，并分析使用这种系统的现实意义。
Introduces a device control system design based on micro -computer parallel port, gives the concrete design method of system hardware and software according to system requirement.
介绍了基于微机并口的某设备控制系统，并根据系统要求，详细讨论了系统的硬件和软件设计方案。
This paper introduced an automatic double flank gear rolling tester based on 8031 single chip computer. It expounded the system hardware, detecting method and the design of software.
介绍了以8031单片计算机为核心的双面齿轮自动检测仪。阐述了系统的硬件组成、检测方法和软件的设计，为齿轮生产提供了一种智能检测仪表。
The system software included upper computer system software and lower computer system software. Method of structural module was adopted in the design of the system software.
系统软件包括上位机系统软件和下位机系统软件，软件的设计采用结构化模块设计方法。
This article presents the method for a design of digital thermometer with AT89C2051 single-chip computer and DS1620. It gives specific circuit and software.
该文介绍了利用AT 89 C 2051控制DS1620设计数字温度计的方法。文中给出了具体的电路和软件设计。
This paper introduces a computer relay protection system based on buses RS-232 and RS-485 and elaborates on the design method of software and hardware for serial communication?
介绍了一种基于RS- 232总线和RS - 485总线的微机继电保护系统，重点阐述了串行通信软、硬件设计方法。
Objective to design an automatic computer software used to estimate the lung volume and the emphysema, to compare the results of computer software with that of manual method.
目的设计计算机自动定量肺体积和肺气肿的软件，并与手工定量方法进行比较。
This method of extending is of such characteristics as simple connection of circuits, easy design of software and consumption of no inner resources of the computer and fast response to interruption.
这种扩展方法具有接口电路简单，软件实现容易，不耗费单片机内部资源，中断响应快的特点。
The article introduces the platform design thinking, the hardware and software composition and operating principle. The design method of emulating bus controller based on computer is emphasized.
文章介绍了该平台的设计思想、硬件和软件组成及原理，给出了基于计算机的仿真总线控制器的设计方法。
The thesis discussed the way to measure cut-point of communication - cables based on AT89C52 single-chip computer, it also gave the method of hard and software design.
研究AT89C52单片机控制的通信电缆断点测试方法，给出了硬、软件的实现方法。
The function and design goal of Wudao chess computer game program is introduced. The key problems processing method and software realizing method of Wudao chess computer game program are presented.
介绍程序的功能、设计目标，给出程序中关键问题的处理方法和软件实现方法。
The function and design goal of Wudao chess computer game program is introduced. The key problems processing method and software realizing method of Wudao chess computer game program are presented.
介绍程序的功能、设计目标，给出程序中关键问题的处理方法和软件实现方法。
应用推荐