The punching die design of external bracket of car pump is elaborated.
详细论述了轿车油泵外用支架的冲压模具设计过程。
Thus the all fiber forging technics is presented and the die design is made.
为此提出了全纤维锻造工艺，并进行了模具设计。
The flow model of extrusion and optimal principles of die design are discussed.
讨论了挤压流动模型、凹模优化设计原理。
The low-pressure casting process and die design for automobile housing were introduced.
介绍了汽车壳体零件低压铸造工艺与模具设计。
This paper introduces a way of inputting picture in CAD system of sectional die design.
介绍了一种用于镶块模c A D系统设计的图形输入方法。
This paper analyzed and introduced the size die structure, die design points and working process.
本文分析并介绍了制动器底板精整模结构、模具的设计要点和其工作过程。
How to optimize the design of Angle bar die and the concrete process of die design are introduced.
介绍如何优化设计角板冲模模具，以及模具设计的具体步骤。
We should seek for an optimal combination of technical effect and economical profit in die design.
设计模具应追求技术效果和经济效益的最佳组合。
Extrusion die design for compound triple-layer plastic pipe by two extruding machines is introduced.
介绍用两台挤出机共挤复合三层塑料管材机头的模具设计。
More than 5 years process or die design, die manufacturing or stamping production process experience.
至少5年以上的工艺或模具设计、模具制造、或冲压生产工艺技术方面工作经验。
So it is very necessary to exploit a practical CAD system for panel trimming and punching die design.
所以，针对覆盖件开发一套实用的修边冲孔模cad系统无疑是十分必要的。
Preform design in bulk metal forming is the central task of bulk metal forming process and die design.
金属体积成形预成形设计，是材料多工序成形工艺与模具设计的中心工作。
The manufacturing process of the small cemented carbide rotors, and extrusion die design are described.
本文阐述了硬质合金小转子的研制过程，并就挤压模设计进行了探讨。
The effect of die design on coating concentricity of optical fiber at high drawing speed is investigated.
研究了在高速拉丝条件下涂覆模具的设计对光纤涂层同心度的影响。
The basic method for aided design on microcomputer is discussed. The mutual CAD system for die design is set up.
论述了在微机系统上辅助设计的基本方法，建立了模具设计的交互式CAD系统。
The die design critical points and advanced pressing process of board spring on rotating shaft steamer dynamotor.
介绍了汽轮发电机转轴上的板弹簧模具设计要点以及先进的压制工艺。
In die design, the pressure center of stamping die is calculated generally using analytic method or schematic method.
在模具设计中，冲裁模压力中心通常采用解析法或图解法求解。
Mould and die design is an innovative process which is mainly dependent upon abundant experience and knowledge from expert.
模具的设计过程是一个建立在设计专家丰富的经验与知识基础上的创造性思维过程。
In die design, the blanking pressure center of stamping die is calculated generally using analytic method or schematic method.
在模具设计中，冲裁模压力中心通常采用解析法或图解法求解。
Discuss punching small thread fluted opening technology, die structure, die design and die manufacture technology on thin sheet.
论述了在薄板冲压件上，用变薄翻边冲制小螺纹底孔的工艺、冲模结构、设计与制作技术。
The selection method of roll forging process parameters of middle tonnage automobile front axle and die design outline were stressed.
论述了中吨位汽车前轴辊锻成形工艺参数的确定方法和模具设计要点。
I am the company's engineering staff of cold stamping die design, manufacturing and product have a deep understanding of the production.
我公司的工程人员对冷冲压的模具，在设计，制造和产品生产有深刻的认识。
The production material thickness will be used when calculating the die design dimensions-check with Project Manager for exact tolerances.
当谋划模具计划尺寸(由项目经理做精确公差的查抄)将利用材料的厚度。
In automobile and metallurgical industry, sheet metal forming numerical simulation has been widely used in material selection and die design.
在汽车和冶金工业中，板成形数值模拟广泛地应用于零件的选材和模具的设计。
All above make it possible to optimize the bulk forming process and the die design in respect of decreasing forming force and saving material.
从而为变形力、变形功与节省材料的角度优化设计体积成形工艺及模具找到了有效途经；
The proceedings required attention during die design and manufacture are pointed out, it can be referenced by similar rolling parts die design.
指出了在模具设计制造中应注意的事项，可为类似滚压件模具设计参考。
Analyzed the status of automobile panel die design, introduced application characteristics of SINOVATION software in automobile panel die design.
分析了目前国内外汽车覆盖件模具的设计现状，介绍了SINOVATION软件在汽车覆盖件冲压模具中的应用特点。
Provision for loading and unloading of raw materials for all dies, as well as part ejection and scrap removal will be covered during the die design.
在扫数模具计划中，必须供给未加工和已加工的工序图，以及产品顶出及废料脱落方法。
Provision for loading and unloading of raw materials for all dies, as well as part ejection and scrap removal will be covered during the die design.
在扫数模具计划中，必须供给未加工和已加工的工序图，以及产品顶出及废料脱落方法。
应用推荐