The load assignment formula and the method of the double circular arc gear under the wiring error influence between the contact mark was introduced and inferred.
介绍并推导双圆弧齿轮在安装误差影响下接触迹间载荷分配的计算公式和方法。
Through the calculation of the finite element method(FEM) models for double circular arc profile spiral bevel gear, the stress changing pattern along the length of the tooth is obtained.
用有限元方法，对双圆弧弧齿锥齿轮沿齿长方向齿根应力进行了计算。通过应力计算结果的分析，得出了凸、凹两齿侧应力沿齿长的分布规律。
Aiming at heavy duty and low speed gear transmission, Zheng Zhou Research Institute of Mechanical Engineering puts forwards ZY-1 case- hardened double-circular-arc gear.
为此，郑州机械研究所针对低速重载齿轮传动领域设计了ZY-1型硬齿面双圆弧齿轮齿形。
The tooth end relief is an effective process for double circular arc gear to lighten the shock, lower the meshing noise, and prevent the tooth end from breakage, so as to prolong the service life.
双圆弧齿轮齿端修形是减小啮入冲击、降低传动噪声、避免齿端崩角、提高使用寿命的有效措施。
A formula is given to calculate the stress in tooth middle of GB12759-91 double circular-arc gear via regression analysis in this paper.
本文用回归分析法求得了GB12759—91型双圆弧齿轮的齿腰应力的计算公式。
The structure parameters have some relation with the vibration behaviors for the reducing box with two stage split flow Novikov gear of with double circular arc tooth profiles.
二级分流式双圆弧齿轮减速箱结构参数对其振动特性有一定的影响。
Its basic gear tooth profile is double circular arc spiral bevel gear tooth profile.
双圆弧弧齿锥齿轮是将点啮合制圆弧齿轮传动形式运用到锥齿轮上的成功例子。
The expression of the axis section profile of grinding wheel used to machine double-circular-arc gear is derived in detail. And the general calculator program is developed.
本文详细地推导出加工双圆弧齿轮的砂轮截面廓形的计算表达式、并研制了通用的计算程序。
The forming process of the double -circular -arc gear is put forward in this article.
并对双圆弧齿轮的成形过程提出了自己的见解。
YCB arc gear pumps are mainly gear, KCG axis, the pump body, cover, the axial bearing, sealing etc. Using double circular-arc gear tooth sine curve.
主要有齿轮、轴、泵体、泵盖、轴承套、轴端密封等组成。齿轮采用双圆弧正弦曲线齿形制造。
The selection of center distance and gear ratio distribution for a reducer with double-circular-arc gear will have a direct effect on its size, weight and loading capacity.
双圆弧齿轮减速器中心距和传动比分配的确定，直接影响减速器承载能力、重量和体积。
The model establishes the base for the 3D digital design, analysis of the finity unit, dummy manufacture of the double-circular-arc gear.
该模型为双圆弧齿轮的三维数字化设计、有限元分析、虚拟制造等奠定了基础。
And in accordance with the relevant literature, the detailed parameters table of the ZY-1 type double-circular-arc gear basic tooth profile is given.
并根据相关文献给出ZY - 1型双圆弧齿轮基本齿廓的详细参数取值表。
The analysis of adjusting errors on processing double circular arc profile bevel gear;
用有限元方法 ，对双圆弧弧齿锥齿轮沿齿长方向齿根应力进行了计算 。
The analysis of adjusting errors on processing double circular arc profile bevel gear;
用有限元方法 ，对双圆弧弧齿锥齿轮沿齿长方向齿根应力进行了计算 。
应用推荐