Edge crack is one of the main factors affecting quality of heavy plates manufactured by Baosteel.
边裂是影响宝钢厚板质量的一个重要因素。
This will bring out edge crack when strip steel rolling. This problem can be solved by annealing again.
导致轧制时出现边裂，采用重新退火，进行退氮处理可解决这一问题。
The edge crack on Q345B wide strip steel was analyzed by means of chemical composition analysis, mechanical property testing, micro metallographical examination.
采用化学成分分析、力学性能测试、显微组织观察和夹杂物检验等方法对有边缘裂纹的Q 345 B宽带钢进行分析。
The optical measurement system of digital image correlation method was established, and the full field displacement of the single-edge crack specimen was obtained experimentally.
通过搭建数字图像相关方法光学非接触测量系统，试验表征含单边裂纹芳纶纤维复合材料试验件在拉伸载荷作用下的全场位移。
The strain fields in damage zone around crack-tip are measured for different strain hardening exponent material specimens with double edge cracks using digital speckle correlation technique.
为了研究粘性效应作用下的扩展裂纹尖端场，假设扩展裂纹尖端的人工粘性系数与塑性应变率的幂次成反比，推导出理想弹塑性材料的一种率敏感型本构关系。
Eagle fell off the edge of the ground crack.
鹰从地面的裂缝边上掉了下去。
Gradually the table light began to spread apart, furthest from the desk edge walk and shop, the area is larger and larger, like a door, only has a crack, and later gradually opened.
渐渐的桌子上的光线开始平铺开来，从最远的书桌沿儿一直往前铺，面积越来越大，像一扇门，先只裂开了一条缝，后来便渐渐敞开了。
The steel reinforcement can be simulated in cementing a strip of ordinary photoelastic material along the crack edge.
沿着裂缝的边缘粘接由普通光弹性材料制成的窄条，即可模拟钢筋。
The transverse crack in surfacing layer, porosity in bead edge and non-fusion between layers are the defects that are liable to produce when multi-layer surfacing is used.
多层堆焊时，易产生堆焊层横向裂纹、焊道边缘气孔及层间结合不良等堆焊缺陷。
The transverse crack in surfacing layer, porosity in bead edge and non fusion between layers are the defects that are liable to produce when multi layer surfacing is used.
堆焊层横向裂纹、焊道边缘气孔及层间未熔合是多层堆焊时易产生的缺陷。
Numerical calculation has been taken for rectangular crack and the distribution of stress intensity factors along the crack edge has been obtained.
对矩形裂纹面进行了数值计算，得到了应力强度因子沿裂纹边界的分布规律。
The measurement of crack height by ultrasonic edge peak echo method and digital signal processing was described, and the results were given.
介绍采用数字信号处理的超声端点反射回波声程测量裂纹高度的方法研究和结果。
Forging defects of mould cavity non-saturate, crack, pucker and shearing edge avulsion, etc. on the astrictive clamps and operating scissors are studied by means of appearance and metallography.
采用外观和金相方法，对止血钳和手术剪锻坯出现的型腔填充不满、裂纹、重皮和切边撕裂等缺陷进行分析。
The crack appears at the edge angle due to stress concentration caused by alternating load, which finally leads to the fissuring of die plate.
凹模在使用过程中，由于交变载荷的作用，使碳化物的棱角处应力集中出现裂纹，最终导致凹模开裂。
Based on the wave surf tessellation grid, surf crack and edge stitching technique, we use method of LOD to decline data sets of ocean surface grid in order to simplify the computation.
在分析海面网格的细化的方法及裂缝和边缘缝合技术的基础上，构造LOD网格以减少网格计算量。
Along the waters edge ice crystals GREw, and listening closely, we heard the crack of freezing.
水边正在结冰，细听之下，有结冻的“咔咔”声。
The edge internal branch crack problems for half-plane in antiplane elasticity are solved with complex potentials and singular integral equation approach.
利用复变函数和奇异积分方程方法，求解反平面弹性中半平面边缘内分叉裂纹问题。
With an aim at some engineering structure features, a single-edge double-crack model is designed.
针对某些工程结构特点，设计了单边双裂纹模型。
In this paper, the behaviour of small crack growth originating at the edge of a hole was studied experimentally and theoretically.
本文对孔边三维短裂纹扩展特性进行试验研究和理论分析。
The results indicated that the largest stress appeared on the edge of Q235 near the interface. This is the key factor inducing crack.
计算结果表明，在靠近结合界面的Q 235钢一侧的工件棱边处产生最大轴向应力，这是导致接头开裂的重要因素。
The edge internal branch crack problems for half-plane in antiplane elasticity are solved with complex potentials and singular integral equation approach.
运用复变函数及积分方程方法，求解了半平面域多圆孔多裂纹反平面问题。
The method that made groove at the edge of the piston with the toroidal combustion chamber and helped to reduce the thermal stress and thermal crack has been discussed. The simulation result...
仿真计算结果表明在收口型燃烧室边缘开适当大小的圆弧槽对减少活塞热裂纹的产生是行之有效的。
Fatigue crack initiating at the free edge of cope hole in the crossbeam is one of primary defects for orthotropic steel deck.
纵肋与横梁交叉部位处横梁弧形切口周边疲劳裂纹是正交异性钢桥面板的主要病害之一。
The plastic zone by the hole edge and its effect on the initiation and propagation of the small crack also were investigated.
对于这类小裂纹扩展机制的分析目前还比较少。
The plastic zone by the hole edge and its effect on the initiation and propagation of the small crack also were investigated.
对于这类小裂纹扩展机制的分析目前还比较少。
应用推荐