The process of flip chip based on aluminum nitride is studied.
研究了以氮化铝为基板的倒扣封装的工艺。
The dynamics of ultrasonic transducer for thermosonic flip chip bonding is investigated.
研究了热超声倒装键合设备的核心执行机构——换能系统的动力学特性。
The embedded active chip also can be realized by backside thinning and flip chip bonding.
通过对芯片进行背面减薄和倒装连接，可以实现有源芯片的埋嵌。
Flip chip technology has become one of the major joining technologies in electronic packaging.
摘要覆晶技术已成为电子构装中之主要接合技术之一。
Flip chip technology has become one of the major joining technologies in electronic packaging.
覆晶技术已成为电子构装中之主要接合技术之一。
Flip Chip on Board (FCOB) has been used widely as a microelectronics packaging structural form.
板上倒装芯片(FCOB)作为一种微电子封装结构形式得到了广泛的应用。
The system can process wafers up to 200mm in diameter and includes die inversion for flip chip applications.
该系统可以处理直径多达200毫米的晶片，包括模具的倒装。
This article presents acid could be used to wash the indium bumps before flip chip bonding, based on indium oxide dissolved in acid.
利用氧化铟易于溶于酸性溶液的性质，提出了在倒装焊接之前使用酸性溶液对铟柱进行酸洗。
This paper talks about the major supporting technologies for MCM package: the Interlinkage of Chips, Flip Chip Bonding, Flip Bonding.
本论文研究了MCM中芯片安装互连、芯片倒装焊接及其关键支撑技术等内容。
Lead in solders to complete a viable electrical connection between semiconductor die and carrier within integrated circuit Flip Chip packages.
集成电路倒装芯片封装中半导体芯片及载体之间形成可靠联接所用焊料中的铅。
Lead in solders to complete a viable electrical connection between semiconductor die and carrier within integrated circuit Flip Chip packages.
集成电路倒装芯片封装中半导体铸模和载波器的焊料中的铅；
An IC chip is mounted by flip chip or wire bonding or adhesive connection on the face of the metal substrate which has the dielectric coating thereon.
IC芯片以倒装焊接或金属线焊接或粘贴连接安装于金属基片的有介质涂层的表面。
Thedrain saturation current is increased 10% after bonding. To disperse heat of GaNHEMT, this flip chip bonding method seems to be simple and effective.
实验结果表明，这种改进的倒装焊技术可以使HEMT 器件的饱和漏极电流提高10%。
This paper introduces the forward trends of flip chip bonding, the essential kinds of bumps, fabrication technology and testing technology about qualities.
介绍了芯片倒装焊的重要意义、发展趋势、基本的焊球类型、制作方法及焊球质量的检测技术。
Electromigration induced Cu dissolution in flip chip Packages The phenomenon of Cu dissolution induced by electromigration at flip chip solder joints is reported.
覆晶封装中电迁移效应导致之铜溶解现象本論文报导覆晶封装之焊点中电迁移所引起之铜垫层快速溶解现象。
With the Doppler laser vibration measurement system, the vibration velocity curves of the flip chip and tool tip were obtained during thermo-sonic flip chip bonding.
采用多普勒激光振动测量系统，获得了热超声倒装键合过程中工具末端及芯片的振动速度曲线。
With optimized circuit design and bump layout, high performance transmission lines for flip chip packages can be achieved using dry film as the masking material for the bump plating.
本实验显示经过最佳化的传输线路设计与凸块分布，低成本高效能的覆晶封装结构目标可以达成。
The methods of 3d interconnection can be classified into the wire bonding, flip chip, through silicon via (TSV) and film wire technology, whose advantages and disadvantages are analyzed.
将实现3d互连的方法分为引线键合、倒装芯片、硅通孔、薄膜导线等，并对它们的优缺点进行了分析。
The design describes the structure of compound die stamping flip-chip design and working process.
本次设计阐述了冲压倒装复合模的结构设计以及工作过程。
Chip scale package (CSP) for flip-chip on hard substrates and wafer re-distribution is studied, and its process flow is described.
对刚性基板倒装式和晶圆再分布式两种结构的芯片级封装（CSP）进行了研究，描述了CSP的工艺流程；
Underfill technology effectively enhances the flip-chip cycle fatigue life and reliability of packaging process.
基 板上的倒装芯片一般采用底部填充技术以提高其封装的可靠性。
And the important role of advanced packagings such as CSP, BGA and Flip-chip technology in the microelectronics is described as well.
论述了如csp、BGA及倒装芯片等先进封装技术在微电子工业中所发挥的重要作用。
In the article experiment prove:combination with feine tin-solder-bumps and underbump-metalliza with cobalt be able to longthen life of leadless flip-chip-solderng.
文章通过试验证明：纯锡焊料凸块和含钴底部凸块金属焊层结合可延长无铅焊接倒装片的寿命。
Based on minimal energy principle, Evolving model of flip-chip 3-d shape prediction of MCM is established, and 3-d solder shape is effectively predicted.
基于最小能量原理建立了多芯片组件(MCM)倒装焊焊点成形预测模型，对其三维焊点形态进行了有效预测。
Based on minimal energy principle, Evolving model of flip-chip 3-d shape prediction of MCM is established, and 3-d solder shape is effectively predicted.
基于最小能量原理建立了多芯片组件(MCM)倒装焊焊点成形预测模型，对其三维焊点形态进行了有效预测。
应用推荐