The forming of automobile′s half shaft by rotary forging technology has been analyzed and a new technological project put forward.
针对汽车半轴摆辗成形进行了工艺分析，提出了一种新的工艺方案。
The loose tooling forging of half shaft bushing on the steam-air forging hammer is numerically simulated using FEM software DEFORM3D.
采用商用有限元软件DEFORM3D对半轴套管胎模锻成形过程进行了计算机模拟。
This paper introduces the design and structure of static torsional testing machine which applied in automobile driving and half shaft.
介绍汽车驱动桥及其半轴静扭试验机的设计思想、总体结构。
Automotive half shaft flange is a coupling part under the combined action of bending and torsion, its strength, loading and actual size have an uncertainty.
汽车半轴凸缘是受弯扭联合作用的联接零件，其强度、载荷及实际尺寸具有不确定性。
In chapter 2, the fatigue mechanism of automobile half shaft is studied; and intensified coefficient model based on fatigue failure theory and programmed load spectrum technology is also provided.
第二章研究汽车驱动桥半轴疲劳破坏机理，在零件疲劳损伤理论和程序载荷谱处理技术基础之上给出路面强化系数模型。
Easy in assembly, involves a mere couple of components per valve (actually one and a "half"), plus a control shaft per row of valves.
在装配简单，涉及到每一个阀组件(实际上是一个和“半”)，仅仅是夫妻，加上每行的阀门控制轴。
The problem of torsion of elastic shaft of revolution embedded in an elastic half space is studied by the Line-Loaded Integral Equation Method (LLIEM).
本文用线载荷积分方程法(LLIEM)研究嵌在弹性半空间的弹性回转轴的扭转问题。
Linking the piston by a connecting rod to a crankshaft causes the gas to rotate the shaft through half a turn.
活塞通过连杆和轴连接，使得气体带动轴旋转半圈。
The valve shaft adopts the half axis structure and the valve plate adopts the girder construction.
阀轴采用半轴结构，阀板采用桁架结构。
The main shaft drives the lay mechanism and is geared to another shaft which operates at half of the speed of the crankshaft.
这样，普通织机应具备两根轴，主轴驱动筘座并通过齿轮驱动另一根轴。
This fact does not contact the shaft seal surface, it is the sealing principle of polymer cooled to half molten state and forming the seal.
这种密封实际上并不接触轴的表面，它的密封原理是将聚合物冷却到半熔融状态而形成自密封。
Thus a normal loom has two shafts. The main shaft drives the lay mechanism and is geared to another shaft which operates at half of the speed of the crankshaft.
这样，普通织机应具备两根轴，主轴驱动筘座，并通过齿轮驱动另一根轴。
Method To link pivot shaft joint strain half dislocation morbidity age and occupation distribution statistical analysis.
方法：对寰枢关节劳损性半脱位发病年龄和职业分布统计分析。
Then check the hole two and a half coupling is the same diameter and length of the original motivation, job machine diameter and shaft length of the size of match.
然后检查两个半联轴节的内孔直径和长度是否同原动机、工作机的直径和轴伸长度尺寸相符。
Then check the hole two and a half coupling is the same diameter and length of the original motivation, job machine diameter and shaft length of the size of match.
然后检查两个半联轴节的内孔直径和长度是否同原动机、工作机的直径和轴伸长度尺寸相符。
应用推荐