Diagram 1: Evolution of leakage current as a function of test voltage.
图1漏电电流随电压变化的函数图。
To determine the leakage current at a particular voltage, apply a step voltage of this magnitude to the circuit.
为了确定特定电压下的漏流,可以向该电路施加一个该幅值的阶跃电压。
Some of these applications may include leakage current of capacitors, reverse diode leakage, or insulation resistance of cables or films.
这类应用可能包括电容器的漏电流、二极管反向漏电、电缆或薄膜的绝缘电阻等。
Low leakage current helps to prolong battery life.
低漏电流有助于延长电池使用寿命。
DC high voltage (or DC leakage current) test is an effective method of technical diagnosis of electric machine.
直流高电压(或称直流泄漏电流)试验,是一种行之有效的电机技术诊断方法。
Humidity can also increase leakage current.
潮湿也会增大漏流。
Suitable for measuring the leakage current of MLCC.
适用于测量mlcc泄漏电流。
For photoflash lug type low loss factor and low leakage current.
闪光灯用焊片式产品,具有低损耗,低漏电等特点。
After cleaning the winding end, the leakage current becomes normal.
清除绕组端部污秽后,泄漏电流正常。
Some of these tests include a variety of leakage current measurements.
其中有些测试工作包括各种泄漏电流的测量。
A leakage current will flow around this loop, but won't affect the measurement.
泄漏电流将在此回路中流动,但是不影响测量。
A new model of leakage current tester of MOA (metal oxide arrester) is introduced.
介绍了一种新型MOA(金属氧化物避雷器)泄漏电流测试仪的研制。
Some failures of 3DK9 switch transistors with higher surface leakage current were analyzed.
针对3DK9开关晶体管在应用中出现表面漏电失效的具体案例进行分析研究。
It is being studied in the world how to reduce leakage current and to obtain the best detector.
如何把漏电流减少到最低限度,从而获得高质量的探测器,是目前国内外正在研究的重要课题。
The effect of aging voltage on the capacitance and leakage current of al electrolytic capacitors.
老练电压对铝电解电容器容量和漏电流的影响。
In other cases, leakage may be expressed as a leakage current at a given voltage, usually the operating voltage.
在另一些情况下,漏电可以用给定电压(通常为工作电压)下的泄漏电流来表示。
The proposed T-type reset switch avoids the leakage current influence effectively during the integrating period.
所提出的T型复位开关有效避免了积分期间复位开关漏电流的影响。
The improvements are most likely due to the reduction of the gate leakage current and the charge injection effect.
这些效能改进的原因可以归之于经过表面处理后,闸极漏电流的降低以及载子注入的减少。
The two most common error sources when measuring high resistance are electrostatic interference and leakage current.
测量高电阻时两个最常见的误差来源是静电干扰和泄漏电流。
To perform the leakage current test, source a specified reverse voltage, then measure the resulting leakage current.
通过施加规定的反向电压,然后测量产生的漏泄电流,即可完成漏流测试。
This guard connection will prevent leakage current from de-energized channels from interfering with the measurement.
保护连接能防止来自去激励通道的漏流干扰测量。
In other cases, the leakage may be expressed as a leakage current at a given voltage, usually the operating voltage.
在其它情况下,漏泄可能被表示为特定电压(通常为工作电压)下的漏泄电流。
Once the leakage current in a given pathway is known and remains consistent, it can be subtracted from subsequent measurements.
一旦知道了给定通路的漏流,并保持稳定,即可从随后的测量值中减去该值。
An algorithm used to analyse the leakage current and the reference voltage simultaneously in frequency domain is also provided.
给出了一种能够同时对泄漏电流和参考电压进行频域分析的算法。
Under both stress conditions stress induced leakage current follows a power law against stress time with different power factors.
在这两种应力条件下,应力导致的漏电流与时间的关系均服从幂函数关系,但是二者的幂指数不同。
Although using metal oxide electrodes can solve the fatigue problem, it is not easy to synthesize and the leakage current can increase.
虽然利用金属氧化物电极可以提高其抗疲劳性,但是这种电极不易制备并且会增加漏电流。
Since the leakage current through the zener diodes results in a voltage drop across the resistor, low leakage zener devices are desirable.
由于流过齐纳二极管的泄漏电流会在电阻器上产生电压降,所以希望使用低漏电的齐纳二极管。
The SourceMeter instrument first performs the necessary DC tests, such as forward voltage, reverse breakdown voltage, and leakage current.
源表首先进行必要的直流测试,例如正向偏压、反向击穿电压和漏流。
The leakage current can be determined by applying a known voltage and measuring the current between either path to ground or path to path.
通过施加一个已知的电压,然后测量通路至地或通路至通路的电流,即可确定漏泄电流。
When the diode is reverse biased, only a negligibly small leakage current flows through the device until the reverse breakdown voltage is reached.
当二极管反向偏置时,仅有很小的、可忽略的漏电流流过,除非是达到反向击穿电压。
应用推荐