The goal behind measuring n executions of task (n >= 1) is to make the cumulative execution time so large that all the time measurement errors I discuss above become insignificant.
度量task的n 次执行的目的在于，让累计的执行时间足够大，从而减少前面讨论的所有时间度量误差的影响。
A shadow moire method and its results for measurement of distortion of aluminium plate at exploding charge is presented. Possible errors are also estimated.
本文介绍了用阴影云纹法测量爆炸载荷下铝板变形的方法及结果，并进行了误差讨论和静态标定。
The relationship between the detection of feature points and the measurement of motion parameters is studied in this instance of ignoring the camera calibrate errors.
在不考虑摄像机内外参数标定误差的情况下，研究了标志点像元的测量精度对运动参数测量的影响。
Nowadays, in order to improve dynamic measurement precision effectively, the correction technique for dynamic errors has become one of the main techniques.
为有效提高动态测量精度，动态测量误差修正技术已成为当今引人注目的主要技术措施之一。
The errors of heading and attitude measurement with GPS are discussed and the schemes are proposed.
通过误差分析，讨论了影响GPS航姿测定的各项误差，提出了GPS航姿测量方案。
But the current measurement of prosperity is riddled with errors and omissions.
但是，当前的繁荣衡量到处都是错误和漏洞。
The origin of measurement errors and measures to improve the accuracy are discussed.
本文还讨论了测量误差的来源和提高测量精度的措施。
Clock error is the main and direct source of errors in network measurement.
时钟误差是网络测量中最主要的直接误差来源。
According to its exponential wave responses, the impulse measurement errors of a digitizer can be calculated.
根据指数波响应，可以计算数字仪的冲击响应和冲击测量误差。
Flexible coordinate system is introduced into theodolite industrial measurement, so there arent errors of instruments levelling and relative orientation in self locating of the system.
将柔性坐标系引入经纬仪工业测量中，使其系统自定位不再受仪器整平误差和相对定向误差的影响。
Experimental results show that the method can calculate the errors of measurement results effectively.
模拟试验结果表明，该计算方法可以有效的计算出测量结果的误差。
Using computer may simulate the errors of measurement result when every parameter varies.
通过计算机模拟系统各参数变化时给测量结果带来的误差。
The impulse measurement errors of the XZF—900 precision resistor divider and the ZRF—1200 low damped capacitor divider are given from exponential wave tests and calculations.
根据指数波试验和计算，文中给出了XZF-900精密电阻分压器和ZRF-1200低阻尼电容分压器的冲击测量误差。
Errors in digital measurement of the peak value and front time of impulses are calculated by this method, with influence factors and variance ranges analysed.
利用这种方法，计算了冲击电压峰值和波前时间的数字测量误差，并分析了误差的影响因素和变动范围。
Systematic errors in measurement of neutron multiplication have been experimentally studied.
实验研究了中子倍增率测量的系统误差。
The causes of errors mainly included two aspects, the standardization of measurement procedures and the psychological factor of individual patients.
产生误差的原因主要包括两个方面，测量过程的规范性和患者个体的心理因素。
Attitude measurement errors of the double cone scanning infrared earth sensor caused by brushless DC motor speed asymmetry was researched.
针对双圆锥扫描式红外地平仪因无刷直流扫描电机转速不均匀造成的姿态角测量误差进行了研究。
When frequency sweeping method being used properly for measuring amplitude-frequency characteristics, the analysis and estimation of errors in measurement results could be avoided.
正确使用扫频法测量幅频特性，可以避免大量测量结果中误差的分析与估算。
The problems of uncertainty estimation are analyzed in detail when measurement results of form errors are evaluated with the methods of least-square and minimum zone.
详细分析了用最小二乘法和最小包容区域法评定形状误差测量结果时的不确定度估计问题。
The measurement of volumetric flow rate will be errors when the parameters of the temperature and pressure change unceasingly.
流体的体积流量受温度、压力等参数的影响，在参数不断变化的情况下，会带来较大的测量误差。
These tests are performed with the axis of rotation passing through the CG to minimise measurement errors.
这些试验都需要轴转动通过重心，以最大程度地减小测量误差。
The errors of harmonic wave analysis and direct sampling in electric parameters measurement are analyzed. The method to minimize errors is presented.
分析了电力参数微机监测中的直接采样计算法与谐波分析法的误差，并提出了减小误差的方法。
The numerical computation shows that the proposed method is able to identify efficiently the concrete thermal parameters while the measurement errors of temperatures are considered.
数值计算结果表明，在考虑到温度观测误差的条件下，所建立的参数反演方法能够有效地识别出混凝土的热力学参数。
Based on analyzing the sources of measurement errors, the correction methods of the errors are introduced and error models of two port calibration are provided.
在对网络分析仪的测量误差来源进行分析的基础上，介绍了误差的主要校准方法，同时给出了二端口校正的误差模型。
According to metrological characteristics of diffraction grating, the measurement error models are built up and the equations between installation and measurement errors of grating are deduced.
根据衍射光栅的计量特点，建立了正交衍射光栅测量误差模型，推导了光栅安装误差与测量误差之间的关系。
Standardized tests are developed by measurement professionals with help of mathematics methods to control errors.
标准化考试是借助数学方法控制测量误差，由职业测量专业人员开发的考试。
Standardized tests are developed by measurement professionals with help of mathematics methods to control errors.
标准化考试是借助数学方法控制测量误差，由职业测量专业人员开发的考试。
应用推荐