The glacier displays alarming signs of increased melt and flow rate.
该冰川显示了令人担忧的迹象：融速和流速越来越快。
That topography means that warm water could progressively melt spots where ice is stuck to the rock, allowing it to flow more freely.
这种地形意味着，升温的海水可日益侵蚀固定于基岩的冰块，一旦所有连接基岩的冰块被消融，冰原将四处游动。
Flow around an obstruction causes a decrease in melt front speed and leads to high local viscosity and reduced relaxation.
围绕障碍物流动使融化前部的速度下降并产生较高的局部粘性而减少松弛作用。
Based on FEM software ANSYS, the dendrites stress states are computed using the results of the melt flow as computing parameters.
使用有限元软件ANSYS，把熔体流动计算结果作为参数，计算了枝晶的受力状态。
Flat sheet dies are heated with electrical resistance cartridge heaters placed in holes drilled in areas carefully selected so as to avoid localized hot spots which would affect melt flow uniformity.
平板模具受筒式电热管加热，这种电热管安装在精选的钻孔中，以避免所在的热熔点影响熔体流动的均匀性。
The higher melt flow rate is also one of reasons.
同时，熔体流动速率控制偏高也是一个原因。
Analyzing the die channel structure and the melt flow of the circle profile in the extrusion die provides the basis of the die design for the circle profile.
分析了模头流道结构和熔体在圆环型材挤出模中的流量，为环类型材挤出模设计提供了依据。
The sample was characterized by melt flow rate and adhesion strength to aluminum.
用熔体流动速度和粘结强度表示试样的特征。
This paper introduces some polymer properties including solid property, melt flow property and some thermal physical properties in the molding.
介绍塑料成型加工过程中固态聚合物性质、熔体的流动性质以及热物理性质等。
Also as dendrites solidify and shrink in volume replacement of melt must flow along a tortuous path of interleaving dendrites.
此外，作为晶体固化和量的收缩，熔化物的替代品一定会沿着交错的晶体网络流过一段曲折的路程。
The die is heated with electrical resistance cartridge heaters placed in hole drilled in placement areas selected to avoid localized hot spots, which would affect melt flow uniformity.
该模具是受电阻加热器加热用，放置在精选的钻孔中，以避免所在的热熔点影响熔体流动的均匀性。
Thermogravimetric analysis(TG), melt flow rate, and oxidation onset temperature(OOT) were employed to characterize the stability of PP containing the antioxidants.
分别采用热重分析、熔体流动速率和氧化开始温度等分析方法考察了其在聚丙烯（PP）中的稳定化作用。
The melt flow index of the blends was increased when the content of PEEK was decreased and melt temperature was increased.
结果表明：共混物的熔体流动指数随PEEK含量的降低和熔体温度的升高而增加；
The effect of blending time on the properties of reactive PP/EPDM alloy was studied via the analysis of gel content, mechanical properties, melt flow behaviour and morphology.
通过凝胶含量测定、力学性能试验以及熔体流动性能测试等手段，研究了共混（反应）时间对密炼法和挤出法反应性PP/EPDM共混合金性能的影响及其机理。
The stable production of the specialty P240 for tubing with large diameter was realized under the condition of low melt flow index.
大口径管材专用树脂P240实现了低熔体流动指数下的平稳控制。
It is pointed out that the testing conditions of plastics properties should near the production and application conditions as far as possible by taking melt flow rate (MFR) for an example.
以熔体流动速率为例，阐述塑料性能测试条件应尽量接近生产和使用条件。
The melt flow indexes of 8 kinds of ABS resins were tested by means of melt flow rate instrument, and the rheological behaviors of the resins were studied by means of capillary rheometer.
用熔体流动速率仪测定了8种ABS树脂的熔体质量流动速率，并用毛细管流变仪对8种ABS 树脂流变性能进行了研究。
The composite material to the mechanical properties, thermal properties and melt flow of the test.
对该复合材料进行了力学性能，热性能和熔体流动性的测试。
The influences of die radius, load and temperature on the flow properties of FEP melt were investigated by using a melt flow indexer.
应用熔体流动速率仪考察了口模半径、载荷及温度对聚全氟乙丙烯（FEP）流动性能的影响。
The results show that: calcium sulfate whisker HIPS modified its mechanical properties have a certain effect of the increase, melt flow increased, but the heat resistance has declined.
研究结果表明：硫酸钙晶须改性HIPS对其力学性能有一定的增强效果，熔体流动性增加，但对耐热性有所下降。
During Exerusion, the polymer melt flow in cone dies was discussed in this paper.
本文讨论了聚合物熔体在圆锥口型中的流动问题。
The results show that the extensional flow of melt in convergent die results in intense entrance elastic effect and distinct extrusion swell in conical die with different angles.
结果表明，不同角度圆锥口模挤出过程中，熔体在收敛流道受到拉伸流变，导致强烈的入口弹性效应，表现出熔体在不同角度圆锥口模挤出时有不同的挤出胀大比。
Melt flow properties and mechanical properties of sulfonated butyl rubber ionomers neutralized by different metallic cations and amines were studied.
研究了不同金属离子及胺中和的磺化丁基橡胶离聚体的熔融流动性及力学性能。
Extrusion rate, melt pressure, flow profile and mixing effects of the conical twin screw with mixing elements were observed experimentally.
对混炼型锥形双螺杆的挤出产量、物料压力、物料流动状态及混合效果进行了大量实验研究。
The effects of the agent system on the modification were investigated by testing melt-strength, melt viscosity, the changes of melt flow rate (MFR) and gel content.
通过熔体强度、熔体黏度测试和熔体流动速率(MFR)、凝胶含量的变化研究了试剂体系对接枝交联改性的作用。
The effects of the agent system on the modification were investigated by testing melt-strength, melt viscosity, the changes of melt flow rate (MFR) and gel content.
通过熔体强度、熔体黏度测试和熔体流动速率(MFR)、凝胶含量的变化研究了试剂体系对接枝交联改性的作用。
应用推荐