Affect the melt flow rate and the cooling speed.
会影响熔体的流动性和冷却速度。
The higher melt flow rate is also one of reasons.
同时，熔体流动速率控制偏高也是一个原因。
The sample was characterized by melt flow rate and adhesion strength to aluminum.
用熔体流动速度和粘结强度表示试样的特征。
During Exerusion, the polymer melt flow in cone dies was discussed in this paper.
本文讨论了聚合物熔体在圆锥口型中的流动问题。
The melt flow phenomenon of flat spiral type die had been studied by 3d numerical simulation.
对吹塑薄膜平面螺旋式模头内熔体流动现象进行了三维数值模拟。
The composite material to the mechanical properties, thermal properties and melt flow of the test.
对该复合材料进行了力学性能，热性能和熔体流动性的测试。
The melt flow index of the blends was increased when the content of PEEK was decreased and melt temperature was increased.
结果表明：共混物的熔体流动指数随PEEK含量的降低和熔体温度的升高而增加；
The network inputs include extruder temperature, die temperature, melt flow rate, air flow rate, die to-collector distance.
网络的输入包括：挤出机温度、喷头温度、熔融体挤出速率、空气流率及接收距离。
A special apparatus was constructed by modifying capillary rheometer to study polymer melt flow behavior through fiber beds.
通过改装毛细管流变仪建立了专门的实验装置，研究高温高压下熔体在纤维床层中的流动行为。
Based on FEM software ANSYS, the dendrites stress states are computed using the results of the melt flow as computing parameters.
使用有限元软件ANSYS，把熔体流动计算结果作为参数，计算了枝晶的受力状态。
The PET melt flow type was estimated to be Newton flow after analysis. And the melt flux was in direct proportion with press fall.
PET熔体流动类型经分析判断为牛顿流动，熔体流量与压力降成正比关系。
The isothermal and Newtonian model for single layer melt flow was analyzed, as well as the non-isothermal and non-Newtonian model.
对于单层模拟，分别进行了等温牛顿模型和非等温非牛顿模型的分析。
The stable production of the specialty P240 for tubing with large diameter was realized under the condition of low melt flow index.
大口径管材专用树脂P240实现了低熔体流动指数下的平稳控制。
The influences of die radius, load and temperature on the flow properties of FEP melt were investigated by using a melt flow indexer.
应用熔体流动速率仪考察了口模半径、载荷及温度对聚全氟乙丙烯（FEP）流动性能的影响。
This paper introduces some polymer properties including solid property, melt flow property and some thermal physical properties in the molding.
介绍塑料成型加工过程中固态聚合物性质、熔体的流动性质以及热物理性质等。
The results showed the fire retardance of PP was affected not only by flame retarding agent used, but also by melt flow ability of the PP system.
结果表明，PP的阻燃性能不仅受所用阻燃剂的影响外，还与体系的熔体流动性能具有很大关系。
The influences of different initiators and their concentrations on grafting ratio and the melt flow rate (MFR ) of the grafted polymer were studied.
研究了引发剂种类及用量对接枝率和接枝物熔体流动速率（MFR）的影响。
Melt flow properties and mechanical properties of sulfonated butyl rubber ionomers neutralized by different metallic cations and amines were studied.
研究了不同金属离子及胺中和的磺化丁基橡胶离聚体的熔融流动性及力学性能。
Analyzing the die channel structure and the melt flow of the circle profile in the extrusion die provides the basis of the die design for the circle profile.
分析了模头流道结构和熔体在圆环型材挤出模中的流量，为环类型材挤出模设计提供了依据。
While the effect of the convection on heat transfer can be neglected at low power densities, melt flow assumes its importance as the power density increases.
随着功率密度的加大，对流的作用增强，其影响不可忽视。
Thermogravimetric analysis(TG), melt flow rate, and oxidation onset temperature(OOT) were employed to characterize the stability of PP containing the antioxidants.
分别采用热重分析、熔体流动速率和氧化开始温度等分析方法考察了其在聚丙烯（PP）中的稳定化作用。
The effects of the agent system on the modification were investigated by testing melt-strength, melt viscosity, the changes of melt flow rate (MFR) and gel content.
通过熔体强度、熔体黏度测试和熔体流动速率(MFR)、凝胶含量的变化研究了试剂体系对接枝交联改性的作用。
A detailed analysis was made on the mechanism of enamel melt flow and the affection of the die construction on the enamel melt in the process of enameling round wires.
本文对漆包圆线的涂漆工艺中漆液流动机理，以及模具结构对漆液的影响进行了较详细分析。
The effect of blending time on the properties of reactive PP/EPDM alloy was studied via the analysis of gel content, mechanical properties, melt flow behaviour and morphology.
通过凝胶含量测定、力学性能试验以及熔体流动性能测试等手段，研究了共混（反应）时间对密炼法和挤出法反应性PP/EPDM共混合金性能的影响及其机理。
Related parameters may be calculated according to the requirements of the enameling process and the theory of enamel melt flow, by using which right die sizes can be selected.
通过漆包线生产工艺对涂漆的要求及漆液流动理论，可以计算出相关的参数，并合理选择配模尺寸。
The die is heated with electrical resistance cartridge heaters placed in hole drilled in placement areas selected to avoid localized hot spots, which would affect melt flow uniformity.
该模具是受电阻加热器加热用，放置在精选的钻孔中，以避免所在的热熔点影响熔体流动的均匀性。
The die is heated with electrical resistance cartridge heaters placed in hole drilled in placement areas selected to avoid localized hot spots, which would affect melt flow uniformity.
该模具是受电阻加热器加热用，放置在精选的钻孔中，以避免所在的热熔点影响熔体流动的均匀性。
应用推荐