• Whereas, with excessive P addition, an extremely low melt viscosity causes balling phenomena.

    但若P元素过量时,则会因熔体粘度过低而导致球化现象。

    youdao

  • Molding shrinkage of small, good stability, melt viscosity size is small, easy forming process.

    成型收缩率小,尺寸稳定性好,熔体粘度小,易成型加工。

    youdao

  • TPS/PEO melt viscosity decreased with the increase of PEO content that made it easily processed.

    随着PEO含量的增加,TPS/PEO共混物的熔体粘度下降,有利于塑化加工。

    youdao

  • The melt viscosity and tensile strength of lithium ionomer increased with the sulfonate content increasing.

    随离聚体中磺酸基含量的增加,锂离聚体的熔融黏度和拉伸强度增大。

    youdao

  • The melt viscosity of the cyclic oligomer is very low which is necessary to impregnate the carbon reinforcement well.

    研究发现环状聚芳醚酮齐聚物熔融温度低,熔体粘度小,具有良好的流动性,十分有利于充模成型及浸渍增强纤维。

    youdao

  • Therefore, the sensory performance and puncture intensity of starch complex film could be predicted by melt viscosity of film liquid.

    采用二次多项式逐步回归法得到淀粉复合膜感官评价、穿刺强度和熔融体黏度等指标的回归方程。

    youdao

  • The electric current and alloy elements in powder system are major factors for influencing melt viscosity in surface metallurgy by plasma beam.

    影响等离子表面冶金熔池中合金熔体粘度的主要因素是电流和粉末体系中的合金元素。

    youdao

  • The addition of 7006A made both the melt viscosity and its shear rats sensitivity of 5200B/7006A decrease, however, its temperature sensitivity increases.

    随7006A含量的增加,5200B/7006A熔体粘度及粘度对剪切速率敏感性降低,而温度敏感性增加。

    youdao

  • It was found that the rheological behavior of UHMWPS is remarkably characterized by its unstable flow at low critical shear rate and ultrahigh melt viscosity.

    结果表明,UHMWPS最显著的流变特征为超高的熔体粘度和低剪切速率下出现不稳定流动。

    youdao

  • The effects of the agent system on the modification were investigated by testing melt-strength, melt viscosity, the changes of melt flow rate (MFR) and gel content.

    通过熔体强度、熔体黏度测试和熔体流动速率(MFR)、凝胶含量的变化研究了试剂体系对接枝交联改性的作用。

    youdao

  • The physical modification improved melt flowing property and decreased melt viscosity of UHMWPE, the modified product could be processed in special or general facilities.

    物理改性提高了UHMWPE的熔体流动性,降低了其熔体黏度,使其能在专用或通用设备上加工成型。

    youdao

  • As the non-newtonian shear rate increasing, the melt viscosity of the PA6 and their blends were decreased, and behave shear thinning, show the Pseudo-plastic fluid features.

    随着非牛顿剪切速率的增加,PA 6及其共混物的熔体粘度明显下降,表现出剪切变稀现象,呈现假塑性流体的流动特征。

    youdao

  • In order to clarify the nature of the transition, the changes of melt viscosity with temperature and shear rate were investigated by capillary rheometer and micro-parallel type rheometer.

    为了阐明转变的性质,用毛细管流变仪和微型平板粘度计研究了其熔体粘度的温度依赖性。

    youdao

  • Moreover, the low molecular weight and higher temperature are favorable to reduce the melt viscosity, to increase the critical shear rate and to improve the apparent quality of extrudates.

    较低的分子量和较高的温度有利于提高临界剪切速率,改善挤出物外观质量和降低熔体粘度。

    youdao

  • The quoted MFR value is the weight of polymer melt flowing through an orifice in specified conditions, so the higher the MFR value, the lower the melt viscosity and the easier the material will flow.

    MF R采用的数值是在一定的条件下通过口模的聚合物熔体的重量,所以MF R越大,熔体粘度越低,而材料的流动性就越好。

    youdao

  • The quoted MFR value is the weight of polymer melt flowing through an orifice in specified conditions, so the higher the MFR value, the lower the melt viscosity and the easier the material will flow.

    MF R采用的数值是在一定的条件下通过口模的聚合物熔体的重量,所以MF R越大,熔体粘度越低,而材料的流动性就越好。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定