Therefore, we are comparatively strong in development and production of motor valve rocker framework assembly and other metal products.
因而具有较强的发动机气门摇臂机构总成及其它金属制品的开发、生产能力。
Most often this is in some kind of valve, but it might also be a belt of motor speed, louver position, and so on.
最常见的是由某种阀来完成，但这也可能是一条皮带，或者是马达速度、口径位置等等。
Electric valve drive motor is generally used to compare the impact resistance to voltage.
电动阀的驱动一般是用电机，比较耐电压冲击。
The implementing agencies including the motor and the electromagnetic valve and so on.
执行机构包括各电动机和各电磁气阀等。
It has profound significance in the development, research and application of the digital valve which USES stepper motor as its driver.
这对于用步进电机作为驱动装置的数字阀的开发研究与应用具有深远的意义。
By means of computered modeling and simulating, the variation of the discrepancy of motor voltage and valve Angle are analyzed when system working at proper or fault condition.
利用计算机建模与仿真的方法，对电动节流阀控制系统正常和异常时电机电压和阀门转角的波动进行了分析。
PID parameters are seek to correct valve-controlled motor system., to reflect actual conditions truer dispersed artificial model is set up with valve-controlled motor for the example.
对阀控马达系统寻求PID控制参数进行校正，为了更加真实的反映实际情况，以阀控马达系统为例建立了离散仿真模型。
The microcomputer controlled test stand 701 adopts power stepping motor to drive the original operating valve to carry out tests.
此种微机控制701试验台，是采用功率步进电机驱动原操作阀进行试验的。
This paper deals with a closed-loop digital control for a hydraulic valve, controlled motor speed system.
研究了用位总线微机构成的液压阀控马达速度闭环数字控制系统。
Integrating application and research technology of DCS and frequency inverter, realize switchover without interference between control valve and frequency-inverter motor in producing process control.
经过DCS与变频控制技术的结合应用与研究，实现了生产过程控制中调频电机与调节阀的无扰动切换。
The paper mainly focus on the experimental research on pneumatic on-off valve motor position servo control system with PCM control method and self-adjusting PID algorithm.
文章主要研究的内容为利用PCM控制技术，采用自适应PID控制算法，对开关阀式气动马达位置伺服系统进行实验研究。
Mount valve against the motor with the ports in corresponding position.
山阀对电机与港口相应的位置。
The new motor-driven devices of valve based on analyses above have been successfully used in industry production.
基于上述分析而重新设计的阀门电动装置已成功用于工业生产。
PLC is as the core of hardware system, and it comprises stepper motor, proximity switch, photoelectric switch, hot resistance, electromagnetic valve et al.
硬件部分采用PLC作为控制核心部件，由步进电机、接近开关、光电开关、热电阻、电磁阀等组成。
Because of the low viscosity of emulsion, valve type orifice was used in emulsion motor and the volumetric efficiency was ensued.
针对乳化液黏度低的特点，将所设计的乳化液马达采用了阀式配流，从而保证了较高的容积效率。
The main products are Various parts of Electric Motor, Generator, Pump, Valve and Engineering machines.
主要产品为各种电机、发电机、泵、阀以及工程机械的零部件。
Valve electric drive motor is generally used to compare the impact of voltage.
电动阀的驱动一般是用电机，比较耐电压冲击。
This paper describes the idle speed control stepper motor type composition, Stepper Motor Idle Control Valve on the main structure, Idle Speed Control Stepper Motor Control Principle of the device.
主要介绍步进电机式怠速控制装置的组成，步进电机式怠速控制阀的主要结构及步进电机式怠速控制装置的控制原理。
And discusses the use of CUT-OFF valve on the hydrostatic bulldozer, points out adding the pressure into the controlling parameter of the diesel motor.
讨论了CUT鄄off阀在液压驱动的推土机上的使用问题，提出将压力引入发动机的控制。
Travel mechanism of each track consists of a variable two-speed piston motor, a planetary reducer and a parking brake, travel brake buffer valve is mounted on motor to reduce hydraulic shock.
每侧履带的行走机构由一个变量双速柱塞马达、行星减速器和制动器组成，行走制动缓冲阀与马达一体安装，吸收了行车时由于制动或载荷变化带来的液压冲击。
This paper give an advice that we can realize closed cycle control of feeding shaft by proportional valve and linear grid ruler instead of servo amplifier and servo motor.
利用比例阀和线性光栅尺配合使用替代伺服放大器和伺服电机实现进给轴的闭环控制。
An integral electronic board, mounted to the side of the valve, may be utilized to control the 4-way directional valve and motor direction (when not using a rotary encoder control).
安装在计量阀侧边的集成电板可用于控制该独特的4通阀门和马达方向（在不使用旋转编码控制器时）。
The steady process of solid rocket motor modulated by the vortex valve is investigated theoretically.
对涡流阀调节固体火箭发动机压强的稳态过程进行了理论研究。
New type electric control big gate valve is introduced, which USES JZ - 7 locomotive brake and it is controlled by microprocessor and stepping motor.
介绍了新型电控大闸采用JZ-7机车制动机，通过微处理器和步进电机实现控制。
This instrument can output 3v power to servo valve and is convenient for testing servo valve and oil motor at site.
本仪器可输出3V电源给伺服阀，便于伺服阀和油动机现场调试使用。
This instrument can output 3v power to servo valve and is convenient for testing servo valve and oil motor at site.
本仪器可输出3V电源给伺服阀，便于伺服阀和油动机现场调试使用。
应用推荐