Screw down mirror on door frame.
将后视镜拧紧到车门框架上。
Screw down any loose floorboards.
用螺钉固定住所有松动的地板。
Adjust it and screw down all the screws.
给予调整。拧紧所有螺钉。
B. Install the door closer and screw down all the screws.
安装闭门器主体并拧紧螺丝。
Straight-through, right angle cast steel screw down vertical storm valve.
直通、直角铸钢可闭立式防浪阀；
This paper introduces the screw down system of this automatic control system.
本文介绍了此机组八辊轧机的压下控制系统。
The product has tendency to clot after moisturizing, screw down the lid after using.
本品受潮后易产生凝固，请使用后盖紧瓶盖。
This paper introduces a electrical and hydraulic control system in screw down device of plate mill.
介绍了应用在中厚板轧机压下装置上的电气及液压自动化控制系统。
Avoid exposing to heat and moisture, screw down the aluminium lid, use immediately after opening up.
本品避免受热受潮，请拧紧铝盖，打开后及时使用。
The valve can be installed in horizontal or vertical. Add seal cushion between two flanges connection and screw down bolt.
本阀可水平安装或垂直安装，安装时两法兰联接中间必须加密封垫片，然后均匀锁紧螺栓。
Clients are not merely trying to screw down fees, but rather are aiming for predictability and fairer, not just lower, bills.
当事人不只是想节省费用，而且在一定程度上是着力于得到一张具有可预见性的、更加公平的，而不只是计费更低的账单。
Pay attention to the direction of medium in valve body. Add seal cushion between two flanges connection and screw down bolt.
安装时请注意阀体上标注介质流向，两法兰连接时必需加密封垫片，然后均匀锁紧螺栓。
Sleeve the invention on the tail-gas tube of the engine, underlay the seal loop in the fixing collar at the two ends and screw down it.
安装时，将本发明套在汽车发动机尾气管上，在两端的固定套圈里垫上密封圈，外面用卡环拧紧便可。
The utility model relates to a conductor kickoff mechanism which can break away from a conductor insulating layer and screw down an electric conductor.
本实用新型涉及一种脱离导线绝缘层的同时拧紧导电体的导线拧脱装置。
This article has described the calculation principle and the main process for the machining of the heavy duty involute screw down worm used for the rolling mill.
介绍了轧机大型渐开线压下蜗杆加工的分析计算原理和主要工艺方法。
The glass's upper and lower, right-and-left, front and back joints size shall be adjusted after the glass installation, and the glass clip will be screw down to fix the glass.
玻璃安装好后，调整玻璃上下、左右、前后缝隙的大小，拧紧玻璃夹将玻璃固定住。
AGC hydraulic screw down system is one of the kernel equipments in hot rolling process, and the product output and quality were directly affected by the state of this equipment.
AGC液压压下设备是热轧工艺中核心设备之一，其设备状态直接影响到产品的产量和质量。
Based on our work practice, the article introduces a parameter selection method for AGC hydraulic system of rolling mills, and analyzes screw down cylinder, power unit and other.
结合工作实践，介绍了轧机压下液压系统的一种参数选择方法，并对压下油缸、油源等进行了分析讨论。
The positive pressure distribution on the bearing surface of screw down system of 950 primary mill was studied using FEM and the corresponding improvement way has been put forward.
通过有限元分析，研究了950开坯机压下系统球面轴承表面正压力的分布情况，并据此提出了相应的改进措施。
Hydraulic gap control system is the key part of accuracy for stripe gauge control of tandem cold rolling mill. Hydraulic screw down system is the most important part of hydraulic roll gap control.
液压辊缝控制系统是冷连轧机组控制带钢厚度精度的关键环节，液压压下系统是液压辊缝控制的最重要的组成部分。
Then, use the aquarium silicone to seal under the flange around all 4 screw holes and around the pipe hole and screw it down with 4 short wood screws.
接着，用水族箱硅胶把法兰盘底、四个螺丝孔以及管孔周围全都涂抹上，然后钻入四枚木螺钉固定好。
In the mechanical design of the system, screw pair drive is applied to achieve the up-and-down movement.
在该系统的机械设计，双螺杆驱动器是用于实现向上和向下运动。
I took out just one screw and the whole thing came down.
我只拿掉一个螺丝钉，整个东西就坍下来了。
Move the feed DOG up or down to perform adjustment, then securely tighten the screw.
上下移动送布牙调节高度，然后拧紧紧固螺丝。
Place a standard nut on the screw and tighten it down securely.
放置一个标准的螺丝和螺母拧紧了安全。
Shipbuilding . sea water valves . screw - down stop - and - check valves with opening mechanism . pattern iv . operating mechanism parts list.
造船工业。海水专用阀门。带打开机构的螺杆向下止动和止回阀。式样。操作机构零件细目表。
A ratchet wheel with a handle is sheathed on the core bar, and a screw can be easily screwed down or unscrewed by both hands.
在芯杆上套上一个带有扳把的棘轮，双手并用，就可以较轻松地拧紧或卸下螺丝。
The control system solves the technical problems of the poor control accuracy, instable torque during assembly and on the like of the prior screw-down tool.
它解决了现有拧紧工具控制准确度差、装配时扭矩不 稳定等技术问题。
The tracking control of the driving and screw-down system is discussed for the purpose of keeping constant tension-difference and overcoming the influences of roll eccentricity, etc.
为保持张力差恒定，克服轧辊偏心等影响，讨论传动与压下系统的最优跟踪控制。
The tracking control of the driving and screw-down system is discussed for the purpose of keeping constant tension-difference and overcoming the influences of roll eccentricity, etc.
为保持张力差恒定，克服轧辊偏心等影响，讨论传动与压下系统的最优跟踪控制。
应用推荐