And the stress distribution can also be improved.
同时节点的应力分布也得到改善。
Finally it analyses stress distribution of the jaw.
最后分析了抓爪的应力分布。
The results were shown by histogram and stress distribution chart .
结果以统计直方图，应力分布图等表示。
High residual stress distribution zone lies in the center of work piece.
平板工件中心存在较大的残余应力分布区。
Objective: To realize normal stress distribution of lumbar vertebral body.
目的：了解正常人腰椎椎体的应力分布特点。
It is very important to know the stress distribution of anchorage zones under cable forces.
掌握锚固区域在斜拉索作用下的应力大小及分布是十分重要的。
The magnitude and direction of force could not change the trend of the stress distribution.
牵引力的大小、方向基本不改变应力的分布趋势。
The stress distribution curve can be obtained directly by a pen recorder with a given scaling.
被测玻璃应力的分布曲线可以直接用记录仪记录。
Meanwhile, the fillet geometry has played an important role on this thermal stress distribution.
同时，钎缝圆角几何形状对这一热应力分布有重要影响。
Objective: To study the traits of intra-stress distribution of lumbar during rotatory manipulation.
目的：研究坐位旋转手法时对腰椎内在应力分布的特点。
By this method, it researches the stress distribution of plane problem for a tooth on synchronous belt.
用此方法对梯形齿同步带一个齿上的平面问题的应力分布进行了有限元分析研究。
Objective: To analyse the difference of the stress distribution during mandible to be forced at the midline.
目的：分析不同年龄的下颌骨正中受力时，下颌骨三维有限元分布的差异。
According to the regulation of axial stress distribution, a way to design the rational end construction is given.
根据端部所呈现的应力分布规律，提出了确定端部合理结构型式的方法。
Objective: To investigate the role of dental collar and post length in determining the stress distribution indentin.
目的：将桩长与牙本质领结合起来进行研究，揭示二者对牙体应力的影响。
Manufacture method of anchor bolt plate is introduced and stress distribution in laboratory is analyzed in this paper.
介绍了锚杆测力托盘的制作方法，在实验室对锚杆托盘的应力分布进行了分析。
The effect of the recessing on the strength and stress distribution of adhesively bonded single-lap joints is discussed.
研究单搭接接头胶缝中预留间隙对接头拉剪强度和应力分布的影响。
This method differs greatly from the present general calculation method in the stress distribution of controlled section.
此法与一般的计算方法相比在控制截面的应力分布方面有大的差别。
Through a large amount of calculation, the stress distribution Pattern of beam axle is obtained for some main load cases.
通过大量计算，对应于几种主要的载荷工况，得到了车桥横梁的应力分布规律。
The whole bond slip curve and bond stress distribution along embedded length were measured by continuous automatic collection.
采用了连续自动的采集方式，测出了较完整的粘结滑移曲线以及粘结应力沿埋长的分布。
Therefore, it is not stress distribution in certain even section but integrate stress flow inside the cap that should be considered.
因此，在厚承台设计时应考虑承台内部的完整应力流，而不是某一平截面上的应力分布。
The last two factors induce borehole instability both by affecting stress distribution around wellbore and material properties of rock.
但后两者都是影响井壁应力分布和岩石力学性能而造成井壁不稳定。
This paper discusses the common problems in the design of frame calculation sketch and stress distribution at corner of the jetted plate.
本文试对框架的计算简图和悬挑板转角处应力分布两个设计中常见的问题作一探讨。
The finite element analysis showed that the normal stress distribution of the grillage wall was about the same as that of the solid wall.
有限元计算表明，网格墙在轴力和水平力作用下的正应力分布与实体墙总体上一致；
Without changing stress distribution, holes are dug in bearing the weight of positions by wiped off material in order to decrease weight.
在各种承载部位，在不改变其应力分布的前提下开设减重孔，利用去除材料来达到减重的目的。
The load -step curve and the stress distribution figures during the deformation and failure process of the concrete specimen were presented.
计算机模拟给出了试件的载荷-加载步曲线和混凝土试件的破坏过程的应力分布图。
The more attention was paid for the effects of matrix, interface and fiber orientation on stress transfer and stress distribution in composite.
研究中主要讨论了基体、纤维和界面的力学性能以及纤维位向的变化对应力传递和应力分布的影响。
For a two-dimensional infinite medium containing an elliptical inclusion of different material, elastic stress distribution formulas are derived.
本文推导了二维无限介质内嵌异性介质椭圆的弹性应力场分布。
Different from photoelastic method, acoustoelastic method does not need transparent model and can measure stress distribution of material directly.
与光弹性方法不同的是声弹性方法不需要透明模型，能直接测量材料的应力分布。
The simulative results show that stress distribution under stretching with superimposed bending is more advantageous to the reduction of spring back.
计算结果表明，先弯曲再拉伸时应力分布规律更利于减小回弹。
The results indicate that under standard load, the installation has good stress distribution, and good bearing capacity because of rational structural design.
结果表明在标准载荷下，该装置应力分布情况良好。同时该装置结构设计合理，承载力大。
应用推荐