By analysis of the middle section stress of the hollow slab in the two situations of consider contact and not consider contact, verified the accuracy of contact finite element model in that situation.
通过考虑接触与不考虑接触两种情况时桥面板跨中截面的受力分析，验证该问题中接触有限元模型的正确性。
The parametric variational principle may be used to finite element analysis as in plastic limit analysis and in elastic contact problems.
如同弹性接触问题及极限分析中那样，该原理可望用于有限元数值分析中。
A general practical finite element analysis model for two-dimentional elastic large deformation contact problems was established using the TL method.
用TL法分析研究，建立了二维弹性大变形接触问题的一般实用有限元分析模型。
Aiming at sheet space structure system, the finite element method in quantitative analysis about contact problem is studied in this thesis.
针对板片空间结构这一结构形式，研究了接触问题定量化分析的有限元方法。
A finite element(FE) model for a tripot universal joint is developed, and a FE analysis on the contact stresses in the parts of the joint under extreme torque is conducted using ANSYS software.
将轿车三枢轴式等速万向节的三维模型经过结构简化离散成有限元模型，并应用ANSYS软件对其承受极限转矩时的内部接触应力进行有限元分析。
Method the Finite Element Method was employed to perform the stress analysis on this valve, which included the material nonlinearity, large deformation and the contact condition.
方法考虑材料非线性，大变形和接触条件建立有限元模型，采用有限元法进行应力分析。
By using a dynamic contact analysis, a finite element model is developed to calculate the response of composite laminates to low velocity impact. A numerical example is given.
利用动力接触分析方法模拟冲击的接触行为，提出了一种新的计算复合材料层板低速冲击响应的有限元模型。最后给出一个算例。
This paper is based on the research of classical contact analysis and Finite Element Method (FEM) contact analysis.
论文对经典接触计算方法与有限元接触问题计算方法进行了对比研究。
In this thesis the generation of orthogonal - aligned - shaft face gear, finite element analysis (fea) of the bend stress and contact stress of the fg drive are studied.
本文主要研究了正交面齿轮的齿面生成、正交面齿轮传动的弯曲应力和接触应力的有限元分析。
Bending stresses and contact stresses of the gears were investigated by finite element method in the static analysis.
在齿轮的静力学分析中，利用有限元的方法对齿轮的齿根弯曲应力和齿面接触应力进行了研究。
Based on the new contact model, finite element analysis scheme of drill rods in contact with curved boreholes is given using Bernoulli spatial curved beam elements.
利用新的接触模型，采用忽略横向剪切变形的三维空间曲梁单元对三维曲井内钻柱的接触非线性进行了有限元分析，给出了一套计算方法。
The finite element analysis of the wheel rail contact shows that the maximum stress under the subsurface exceeds first yield strength, which leads to plastic deformation.
在对轮-轨系统进行有限元分析的基础上，研究了轨道的受力情况和摩擦系数对应力分布的影响，讨论了轨道的弹塑变形和安定极限。
Therefore, based on rolling bearing implicit finite element solution analysis, using ANSYS/LS-DYNA explicit dynamic module implements, we achieved the rolling contact simulation of motion process.
因此本文在对滚动轴承有限元隐式求解分析的基础上，利用ANSYS/LS-DYNA模块对滚动轴承进行了显式动力学接触分析。
The 3-d finite element model of bolt is calculated by the method of contact analysis, and the fatigue strength of bolt is checked.
并采用接触分析法对螺栓的应力应变进行了三维有限元计算，对螺栓的疲劳强度进行了校核。
An engineering soft ware adapted to the finite element analysis of three dimensional contact stress in aircraft cylindrical gears is provided.
提供了一个适用于航空圆柱齿轮三维接触应力有限元计算分析的实用工程软件。
The integrated finite element stress analysis for a bladed disk assembly has been carried out, using the cyclic symmetric model with contact surfaces.
本文用含接触面的循环对称计算模型进行轮盘-叶片组件的统一有限无应力分析。
The methods of dealing with the contact problems by the finite element method are researched in this thesis, and calculation and analysis combining engineer examples are carried on.
本文就采用有限元法求解接触问题进行了研究，并结合工程实例做了计算与分析。
Based on the broken gear teeth in contact fatigue test, bending fatigue life curve was got by applying finite element stress analysis results, MSC.
本文以接触疲劳试验中疲劳断齿齿轮为依据，利用有限元应力分析结果以及试验得到的弯曲疲劳寿命曲线，应用msc。
In accordance with the theory of contact mechanics an analysis is made upon rolling bearings by means of finite element method and a new method of unsymmetric shape modification for roll...
根据接触力学理论，通过有限元方法对滚动轴承的分析，提出了滚子非对称修形新方法。
The contact analysis between guide and slider of column of a certain type welded structure horizontal machining center is analyzed by the finite element analysis software of ABAQUS.
运用ABAQUS有限元分析软件，对某型焊接结构卧式加工中心立柱导轨与滑块进行接触分析，得到二者在钻孔下的接触应力、变形分布情况。
The contact analysis between guide and slider of column of a certain type welded structure horizontal machining center is analyzed by the finite element analysis software of ABAQUS.
运用ABAQUS有限元分析软件，对某型焊接结构卧式加工中心立柱导轨与滑块进行接触分析，得到二者在钻孔下的接触应力、变形分布情况。
应用推荐