Rotating the polygonal head with tools to tightening bolt and the object can be fixed on the structure.
通过工具旋转上述多边形头部，紧固螺栓，将 上述被紧固物紧固于结构物上。
Sensor bolt to be used to ensure a certain degree of tightening torque, prolonged use will not become loose.
传感器要采用螺栓固定，保证一定的紧固力矩，长时间使用不会松动。
Control squeeze shoulder bolt prevents over tightening of the clamp assembly, preventing the possibility of crushing the tube.
控制螺栓防止挤肩以上的夹具装配紧缩，防止粉碎管的可能性。
The value of tightening torque is relative not only to the nominal diameter and quality class of the bolt, but also to the security of the threaded fastener.
指出螺栓联接的扭紧力矩值不仅与螺栓的公称直径及性能等级有关，还与能否保证联接可靠工作有关。
It also expounds importance of using new cylinder-head bolt tightening methods to assembly of cylinder-head.
从理论上论述了采用新的缸盖螺栓拧紧法对发动机缸盖装配的重要性。
This article studies the influence of the bolt tightening torque on the fretting damage of LY12CZ aluminium alloy double shear lap bolted joint by experimental and conumerical analysis.
从试验和数值分析两个方面研究了螺栓预紧力矩对LY12CZ铝合金双盖板对接螺纹联接件微动损伤的影响。
Flooding irrigation motor bolts should be open, filled with clean water after the bolt tightening, and then dive into the water.
水浸电机应打开灌水螺栓，灌满洁净的清水后拧紧螺栓，再潜入水中。
Recommended bolt tightening slowly reached up to allow the scope of leakage.
建议慢慢扭紧螺栓直至泄漏量达到允许范围。
Through the analysis to the test results, how to set up a reasonable tightening process for cylinder head bolt is expounded.
通过试验分析，阐述了如何合理地制定缸盖螺栓的拧紧工艺。
Uniform bolt tightening. It is helpful to railway construction and maintenance.
螺栓拧紧质量均匀，是铁路线路施工和维修的好帮手。
Fasteners, the bolt tightening torque of 65 n. M, shall not be destroyed.
采用的扣件，在螺栓拧紧扭力矩达65n.m时，不得发生破坏。
The junction of bonding jumper should be clean and covered with conductive paste. And the tightening moment for bolt must fit with equipment wiring requirements.
接线搭接面确保清洁，涂抹导电膏，螺栓紧固力矩符合设备接线要求说明。
It is possible for the bolt stress to decrease after initial tightening, because ofslow creep or relaxation of the gasket, particularly in the case of the "softer" gasket materials.
[S-1]在螺栓被初步紧固之后，由于垫片的缓慢蠕变或松弛，特别是采用的是“比较软的”垫片材料，则螺栓应力的下降是可能的。
Once that is done THEN tighten the center bolt and follow by tightening the support knob.
中心螺栓和脚架支撑盘也已经一体化设计进去了。
The paper analyzed the bolt pre-stress affected to the mine roadway support effect and the relevant relationship between the bolt pre-tightening torque and the pre-tension.
分析了锚杆预应力对巷道支护效果的影响，锚杆预紧扭矩与预紧力对应关系。
The utility model is not easy to loose and rotate after tightening, so as to effectively improve the service life of the hub bolt and the hub.
本实用新型在拧固后不易松动旋转，有效地提高了轮毂螺栓和轮毂的使用寿命。
When the screw bolt is rotated, the washer is forward pushed out, and thereby, the steel wire ring is tightly connected to realize the purpose of tightening ring.
隔板、垫圈位于螺栓上，其中钢丝环引出端从环的切线方向引出后被固定于隔板及垫圈上。
When the screw bolt is rotated, the washer is forward pushed out, and thereby, the steel wire ring is tightly connected to realize the purpose of tightening ring.
隔板、垫圈位于螺栓上，其中钢丝环引出端从环的切线方向引出后被固定于隔板及垫圈上。
应用推荐