The research on the technologies of micro wire electrical discharge machining (micro-WEDM) was presented.
为进一步研究气中电火花线切割加工工艺规律提供了理论依据。
The influence of peak current on finishing high-speed wire electrical discharge machining (WEDM) in gas and emulsion dielectric is studied.
研究了在大气和乳化液两种介质中，峰值电流对高速走丝电火花线切割加工的影响。
Voltage between tool and workpiece is an important parameter in the on line monitoring of wire electrical discharge machining (WEDM) process.
电火花线切割加工时工具(电极丝)和工件之间的放电电压是对放电加工过程进行实时检测的重要参数。
A new WEDM (Wire Electrical Discharge Machining) technology for finishing cut has been developed, in which gas has been used as a dielectric instead of water.
用气体介质代替液体介质，开发出了一种新型的电火花切割精加工工艺。
Wire Electrical Discharge Machining (WEDM) process is changeable and difficult to control quantitatively. Many factors influence the process and they are related and contradictive.
电火花线切割加工过程复杂多变，难以定量控制，影响因素较多，相互关联又相互矛盾。
Based on analyzing the characteristic of MWEDM (Micro wire electrical discharge machining), the key techniques are studied for meeting the needs of high precision and surface integrity.
在分析微细电火花线切割加工特点的基础上，对获得高精度、高表面质量工艺指标的关键技术进行了研究。
So, from the point of practical engineering application, it is of great realistic significance for this theme to develop software for computer programming of wire electrical discharge machining.
因此，本论文从实际工程应用的角度来开发低速走丝电火花线切割微机编程软件，是具有现实意义的。
Wire Electrical Discharge Machining Milling (wire EDM-Milling) is a novel kind of EDM-Milling method that has the distinct advantage of electrode compensation via the wire electrode slow traveling.
线电极放电铣削加工是一种新型电火花铣削技术，它的最大优点是可通过线电极的缓慢移动来补偿加工中的电极损耗。
Whether the wire winding system of LSWEDM(low speed wire electrical discharge machine) can run stably directly affects the machining accuracy and machining surface quality.
低速走丝电火花线切割机走丝系统是否能稳定运行，直接影响着加工精度和加工表面质量。
The core technique problems during wire cut electrical discharge machining in the inner conductor sheet were analyzed by this paper.
分析了板线内导体在利用数控电火花线切割加工中所遇到的工艺技术难题。
The newest trends of electrical discharge machining (EDM) including die-sinking EDM, micro EDM and wire EDM (WEDM) in Japan were presented.
综述了日本在放电加工领域的最新研究动态，包括成形放电加工、微细放电加工和线切割放电加工三部分内容。
This paper investigates the high speed wire electrical-discharge machining (HSWEDM) of Si3N4-based ceramics by assisting electrode method.
通过辅助电极利用高速走丝电火花线切割加工的方法对绝缘陶瓷氮化硅作了加工实验研究。
This paper investigates the high speed wire electrical-discharge machining (HSWEDM) of Si3N4-based ceramics by assisting electrode method.
通过辅助电极利用高速走丝电火花线切割加工的方法对绝缘陶瓷氮化硅作了加工实验研究。
应用推荐