采用进口轴密封，能承受高背压。
是一种较理想的轴密封装置。
本文介绍了三组不同支座的轴密封部件试验结果。
This paper presents experimental results for shaft seal assembly with three kinds of different support seats.
本文根据尾轴密封装置的工作实际，提出一种新的传热模型。
Based on the practical operating condition of the stern tube sealing system, a new model of heat transfer is presented in this paper.
可靠的轴密封设计，能承受高背压，可以串并联使用可以串并联使用。
Credible design of shaft seal, which can bear high pressure and be used in parallel or in series.
主泵由三个部分组成(由下而上)：水力部件，轴密封部件和电机部件。
The pump consists of three sections from bottom to top: the hydraulic section, the shaft seal section and the motor section.
高速大长径比搅拌轴密封可靠性问题，一直是从事密封工作者探索的问题之一。
The question about the seals of high speed churn shaft with large ratio of length to diameter is one of the difficult problems.
高速大长径比压力反应釜搅拌轴密封性能问题一直是设计者与使用者研究的难题。
The sealing property problem for the stirring shaft of high-speed pressured reaction axe with large length to diameter ratio is always a difficult problem to study for designers and users.
通过分析某船艉轴密封的构造，为提高其使用寿命，改装设计了一种新型艉轴密封装置。
To prolong the longevity of the tailshaft sealing, here we introduce a newly refitted tailshaft sealing by analysing its structure.
介绍了磁流体往复轴密封的原理，从摩擦学设计角度分析了其设计和使用中要注意的问题。
The principle of magnetic-fluid reciprocating shaft seal is introduced, some problems of its design and application are analyzed from the point of view of tribological design.
层状剪切式密封系统是一种技术较为先进的轴密封系统，特别是对于大型水泵轴密封，能取得良好的效果。
Stratified shear packing seal system is an advanced axle seal system, which can achieve good result, especially for large water pump axle sealing.
泵主要由泵体、泵盖、叶轮、轴、密封环、中间支架、密封和悬架部件等组成。
The pump comprises mainly of pump body, cover, impeller, shaft, seal ring, intermediate support, sealing and suspension assembly, etc.
kcb齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。
KCB gear pump are mainly gear, shaft, pump body, valve, shaft end seal.
密封空气被注入到主马达轴（顶部和下部）和驱动马达的齿轮轴的迷宫式密封里。
Seal air is injected into the labyrinth seals located at the main motor shaft (top and bottom) and at the pinion shaft driving the motor.
内啮合齿轮泵的结构和其他齿轮泵结构类似，主要由外转子、转子、泵轴、泵体、前盖、托架、密封装置、轴承等组成。
Internal gear pump structure and other gear pump structure similar to, mainly by the outer rotor and rotor, pump shaft, pump body, the front cover, bracket, sealing device, bearing, etc.
主轴调质措置的首要位置是轴承位、密封位及轴头和叶轮位。
Spindle quenched renew prime location bearing position, sealing position and the spindle head and impeller position.
离心泵的基本构造是由六部分组成的，分别是：叶轮，泵体，泵轴，轴承，密封环，填料函。
Basic structure of the centrifugal pump is composed of six parts, namely: impeller, pump, pump shaft, bearing, seal ring, stuffing box.
转动轴腔充气密封，消除了粉尘粘结现象。带自动清洗功能。
The rotation drive shaft is sealed with inflatable chamber, eliminating the dust coalescence phenomenon. There is a function for automatic cleaning.
最后，在组装过程中，当部件通过键槽时，注意避免损坏密封和轴的轴颈表面。
Lastly during assembly care is taken to avoid damaging the seals when passing over the keyway or performing bearing surfaces of the shaft.
针对离心通风机传动组的轴端密封经常漏油这一现象，提出了改进措施。
Improving measures are put forword against the phenomenon of shaft end seal of oil leakage of centrifugal fan driving unit.
在轴上开出沟槽或装上油环，借离心力将沿轴表面外流的油甩掉，集结后流回油池，因而起到密封的作用。
Out in the shaft loaded oil ring groove or by centrifugal force along the axis of the oil drain off the surface, the oil flows back to the assembly after the pool, and thus play a role in sealing.
筒体与轴两端的相连处装有四重轴端密封装置。
Two ends of the mixing axis that articulates with the mixing silo are loaded quadruple axle end seal device.
动力启动方轴传动装置。销法兰。无油密封垫圈。
Power take - off, squared shaft drive. two stud flange without oil seal gasket.
船舶尾轴的辛泼来克司密封环形状非常复杂，用一般方法难以进行分析。
The shape of the Simplex stern tube seal ring is so complicated that its characters can not be analysed by ordinary methods.
泵轴端密封设计为两种形式，一种为机械密封，一种是填料密封，可根据具体使用情况和用户要求确定。
Pump shaft seal is designed to end in two forms, one for the mechanical seal, one is packing seal, may be based on specific usage and user requirements to determine.
为防止轴穿出泵壳处轴周围的泄漏，使用填料或密封。
Packing or seals are used to prevent the pump leaking around the shaft where it emerges from the pump case.
该搅拌机主要由搅拌筒体、搅拌轴及其轴端密封装置，以及主传动机构和卸料机构等部分组成。
Tthe mixer is primarily composed of mixing silo, mixing axis and their axle end seal device, main drive gear and discharging mechanism etc.
该搅拌机主要由搅拌筒体、搅拌轴及其轴端密封装置，以及主传动机构和卸料机构等部分组成。
Tthe mixer is primarily composed of mixing silo, mixing axis and their axle end seal device, main drive gear and discharging mechanism etc.
应用推荐