酒槽鼻能治好的吗？
Right-click to set chamfer angle.
右击可设置切角角度。
Or just the dimensions related to big chamfer?
或者只是尺寸大倒角？
Drag onto the page. Right-click to set chamfer Angle.
拖到绘图页上。右击可设置切角角度。
Next, chamfer the part so that it appears as the drawing.
下一步，倒角的一部分，所以它似乎作为绘图。
Optional accessories are: to plug, referral chamfer, outlet.
可选配件有：地插座、下线槽、出线口。
Marking chamfer and taper is a routine work in Mechanical drawing.
在机械制图中，通常需要进行大量的倒角和锥度的标注工作。
Gingival margins can be prepared with a deep chamfer or a shoulder.
可以制备深凹肩台或者直角肩台。
After the part is complete chamfer all corners and relieve all burs.
部分完成后，倒角的各个角落，减轻所有钻。
Table 1 – Accepted deiation for linear measurement except for chamfer edges.
表1---除倒角外，所有线性尺寸的公差标准。
Chamfered washer or spacer with adjustable inside and outside diameters and chamfer.
内径和外径以及斜面都可调整的切角垫圈或垫片。
But for Reminder: the dimensions related to big chamfer are not major characteristic.
但提醒：大倒角的尺寸并不大特点。
CHAMFER: the flat surface formed by cutting away the sharp edges of two meeting surfaces.
倒角：两个表面相交处，通过切掉尖锐边缘形成的平面。
The part of gradient coil near shell forms chamfer Angle to lay more sound absorption material.
所述梯度线圈靠近外壳的部分形成倒角，以放入更多的吸声材料。
The so-called bearing chamfer, that is, the horizontal and vertical bearing surface of the junction.
所谓轴承的倒角，就是说轴承的横面与竖面的交接处。
The Chamfering machine is a kind of special machine that mainly used to chamfer the end of pipe & tube.
倒棱机是一种专用机床，主要用于对钢管端部进行平头及倒棱加工处理。
In assembly drawings, certain technical structures, such as round, chamfer, and undercut can be omitted.
对零件的工艺结构，如小圆角、倒角、退刀槽等可省略不画。
To create a smooth transition select edges along connection of the wall and the floor and apply Chamfer.
如果你要创建平滑的过渡，你可以沿着墙和地面交界的边，然后进行倒角。
With three-dimensional inclined slot features its uniqueness in a slight chamfer at the edge of the floor panel.
模压立体斜槽地板的独特之处就在于，地板的侧面有轻微的倒角。
Rolling bearings. single - row cylindrical roller bearings. chamfer dimensions for loose rib and non - rib sides.
滚动轴承。单列圆筒形滚子轴承。平挡圈和非凸缘边的倒圆角尺寸。
Select those front edges and chamfer them then click apply and chamfer it again but this time with a lower value.
选择前面的边并倒角，然后单击应用并以较低的值再次倒角。
Rolling bearings. single - row angular contact ball bearings. chamfer dimensions for outer ring non - thrust side.
滚动轴承。单列角面接触的球轴承。外圈非推力边的倒圆角尺寸。
In addition, tools like floor generator and quad chamfer are really helpful and further speed up the modeling process.
此外，像地板生成器和切角工具十分有用，也进一步加快了建模过程。
The length of chamfer shall be between1 and2 complete threads as measured parallel to the axis of the threaded component.
当平行于螺纹构件轴线方向进行测量时，倒角长度应该在1-2全螺纹扣之间。
Up chamfer, down chamfer and working face must be correctly dressed so that the valve seat can acquire a longer service life.
气门座要获得高的使用寿命就必须对其上、下倒角和工作面进行适当的修整。
And it also point out that the Angle of chamfer and the accuracy design of chamfer start bit are very important to the whole design.
本文介绍滚刀倒角角度和倒角起始点的精确设计与计算方法。
Then I added a smoothing modifier to clear unwanted smoothing's and then a quad chamfer modifier on top to get chamfer for all edges.
然后我进行了平滑修饰，将所有我不想要的弧线去掉，最后在四个斜面顶部进行修饰，得到所有的边缘倒角。
The cause and mechanism of valve failure are analyzed, and the method of tumbling chamfer is studied to improve service life of the valves.
综合分析了阀片的失效原因、机理，并进行了对阀片边缘实施滚磨倒角来提高其疲劳寿命的实验研究。
The cause and mechanism of valve failure are analyzed, and the method of tumbling chamfer is studied to improve service life of the valves.
综合分析了阀片的失效原因、机理，并进行了对阀片边缘实施滚磨倒角来提高其疲劳寿命的实验研究。
应用推荐