The simulation results show that the cold extrusion process can greatly save copper materials and reduce production cost.
模拟结果表明,所提出的冷挤压工艺可以极大地节省铜材料,降低生产成本。
It is worth while recommending this steel for manufacturing cold extrusion dies, because it not only reduces the production cost through saving alloying elements, but also prolongs the die life.
新钢种作为冷挤压模具用钢,既节约了合金元素,降低了成本,又提高了模具寿命,具有推广价值。
The cold extrusion process can ensure forming of the cylinder.
该工艺保证了该零件圆柱部冷挤压成形的顺利进行。
An example shows the application of the CAD of cold extrusion die for slot wedge.
并结合一个应用实例来说明槽楔冷挤模cad系统的应用。
The problem of cold extrusion for inner ratchets of bicycle's flywheel was discussed.
探讨自行车飞壳内棘齿的冷挤压成形问题。
Simulated test method-the method for estimating pressures of cold extrusion is presented.
提出了一种估算冷挤压力的方法一模拟试验法。
There are lots of advantages by cold extrusion for straight knurl nut in a single process.
直纹滚花螺母采用冷挤压一次成形新工艺,成效显著。
There are lots of advantages by cold extrusion for straight knurl nut in a single process.
纹滚花螺母采用冷挤压一次成形新工艺,成效显著。
Such as sheet metal blanking, bending, stretching, fine blanking, the cold extrusion of metal parts.
如板材的冲裁、弯曲、拉伸、精冲、冷挤压金属零件。
This paper studies and discusses the forming analysis and forming method of cold extrusion for precision gear.
对精密齿轮的冷挤压成形分析、成形方法进行了概述。
The article introduces the application of twisted steel sleeve cold extrusion technology to construction in detail.
详细介绍了带肋钢筋套管冷挤压技术在施工中的具体应用。
This paper mainly performs the design and mechanical analysis and research on cold extrusion mold of the gear axis in cars.
本文主要对汽车用齿轮轴的冷挤压模具进行了设计和力学分析研究。
The knowledge representation methods and fuzzy reasoning mechanism of a cold extrusion process planning system were researched.
研究了冷挤压工艺设计领域的知识表示以及冷挤压工艺设计系统的模糊推理机制。
Numerical simulation on cold extrusion process of automobile starter socket has been carried out by using the software DEFORM3D.
采用塑性成形有限元分析软件DEFORM3D,对汽车启动器套筒冷挤压齿部成形过程进行了数值模拟。
The forming process, die design and some manufacturing main points in cold extrusion of piston pins are presented in this paper.
介绍了活塞销冷挤压的生产工艺、模具设计及制造特点。
An analysis on the cold extrusion process and a technological experiment were made for the two spline ends of a slim drive shaft.
细长传动轴两端花键头进行了冷挤压加工分析与工艺实验。
In this paper, the cold extrusion process of 7a04 aluminum alloy was developed for the production of a double-cup workpiece with a deep hole.
针对一种具有深孔的双杯形零件,对7a04铝合金复合冷挤压工艺进行了研究。
In this paper, the advantages of the manufacturing on the cutting copper tube joint with the cold extrusion heading technology are pointed out.
文中指出了采用冷挤镦工艺代替切削加工生产铜管接头的优点。
Cold extrusion force is the key of the success of cold extrusion process. The calculation of extrusion force is usually completed by manual work.
冷挤压力的高低是冷挤压工艺成败的关键,通常挤压力计算是人工完成的。
The verification tests of cold extrusion process and fatigue life of a spline shaft show that the analysis results agree well with those of testing.
经花键冷挤压工艺试验和疲劳试验验证,分析结果和试验结果吻合很好。
The working process, structure and control system of a three-dimensional manipulating robot for cold extrusion forming of metal have been introduced.
介绍了用于金属冷挤压成形的三维操作机器人的工作过程、结构与控制系统。
The forming process by cold extrusion for the hood pedestal of the auto air_conditioner compressor and the design of the cold extruding die were introduced.
介绍了车用空调压缩机罩体支架的冷挤压成形工艺及冷挤压模具设计,采用工艺试验的方法确定挤压坯料尺寸。
Form and dimension may also be achieved by a number of alternative processes such as hot or cold extrusion, sand casting, die casting, and precision casting.
形式和尺寸也可以通过其它一些可选工艺来达到,比如热挤出或冷挤出加工,沙模铸造,拉模铸造,或精密铸造。
A powerful drawing-thickening technology was prompted for double-cup-shaped workpieces, it combined the characteristics of cold extrusion with drawing process.
结合冷挤压与拉深工艺的特点,以双杯形工件为对象,开展了冲锻成形过程的强力拉深增厚工艺研究。
The effect of blank quality in cold extrusion on the damage way and service life of working parts (mould and die)is analysed, and some countermeasures presented.
分析了冷挤压毛坯质量对模具的工作部分(上、下凸模和凹模)的损坏形式和寿命的影响,指出了保证毛坯质量应采取的措施。
Based on the analysis to the current spline forming process at home and abroad, the spline tube forming process was studied and the cold extrusion process was suggested.
本文在研究国内外花键生产的基础上,对内外空心花键管的成形进行了工艺性分析,提出了花键管的冷挤压工艺。
This paper studies the influence of both punch shape and constructivetechnological factors as well as the compressive and tensile stresses on the endurance of cold extrusion punches.
研究了凸模形状、结构- 工艺因素、压应力和拉应力对冷挤压凸模耐用度的影响。
The advantage of the gear axis with cold extrusion technology replacing metal cutting working production are narrated, and the technological analysis for the gear axis part is conducted.
叙述了采用冷挤压工艺代替切削加工生产齿轮轴的优点,并对齿轮轴零件进行了工艺分析。
By comparing experimental results with prediction data, they fit well, which provides a new method to research open-die cold extrusion. and to create expert system of its technological design.
通过实验结果与预测结果的比较,二者吻合良好,为深入研究开式冷挤压工艺,建立开式冷挤压工艺设计专家系统提供了新的思路。
The prestressing force in combined dies to be used for cold extrusion of bearing outer race by the two mathematical models is calculated and compared with the results obtained by Lame formulae.
利用这两种模型分别计算了轴承套圈冷挤压组合凹模的预应力,并同拉美公式的计算结果进行了分析比较。
应用推荐