The cooling rate and denudation rate decreased overall from north to south.
总体上自北而南，剥蚀速率和冷却速率均逐渐变小。
The critical cooling rate for the glass formation in the tube was determined.
确定了在落管中形成玻璃的临界冷却速率。
Two methods for reducing cooling rate during underwater wet welding are studied.
研究了两种能应用于水下湿法焊接的缓冷方法。
The glass transition temperature of PLLA decreased with the increase of cooling rate.
玻璃化温度和结晶度随着降温速率的降低而增大。
The cooling rate is faster in chromite sand mold, but also causes more porosity in castings.
铬砂制作的砂模可让铸件有较快的冷却速率，但也产生较多的微孔隙。
The atmospheric radiation balance and the net radiation cooling rate in tropo-spheric layers.
对流层内各层大气的辐射差额及其辐射冷却率。
Finally, I tested the parsing by checking to see if the object contained a cooling rate multiplier.
最后，通过检查此对象是否包含冷却率乘数测试解析过程。
The strength of waxy structure and gelation temperature decreased when increasing cooling rate.
降温速率越高，测量温度下蜡晶结构强度和胶凝温度越低。
However, the cooling rate obtained in these tests was very difficult to do under the industrial scale.
然而，实验室条件下试验所达到的冷却速率在工业化生产中较难实现。
In addition, lengthening the cooling time or lowering the cooling rate can reduce the residual stresses.
另外，延长喂料冷却时间或降低喂料的冷却速率有助于减小残余应力。
The Raman spectroscopy measurements indicate that silicate glass structure is insensitive to cooling rate.
拉曼光谱检测显示，硅酸盐玻璃的结构对降温速度变化不敏感。
The results indicate membrane permeability and cooling rate are main factors that affect the cell shrinkage.
计算结果表明，膜的渗透性和冷却速率是影响细胞体积收缩的主要因素。
The transformed ferrite volume fraction increases and grain size decreases with the increase of cooling rate.
随着冷却速率的增加，铁素体体积分数减少，晶粒尺寸变细。
The main factors that affect the grain refinement are heating and cooling rate, holding time and cycle index.
影响细化效果的主要因素有：加热速度、保温时间、冷却速度和循环次数。
The transformation rule of diameter of droplets between cooling rate and undercooling can be analyzed in drop tube.
对落管中冷却速率和过冷度随液滴直径的变化规律进行了分析。
The more the increase of cooling rate or pre-deformation, the more the secondary dendrite arms are easy to coarsen.
冷却速率越大或预变形处理以后的试样在熔化过程中更容易发生二次枝晶臂之间的合并。
The maximum thickness of amorphous alloy ribbons can also be determined by this formula and the critical cooling rate.
由这个公式和临界冷却速度还能决定出非晶态合金丝带的最大厚度。
For maximum softness and ductility the cooling rate should be very slow, such as allowing the parts to cool down with the furnace.
为了得到最大柔软性和延展性冷却速率应该很慢，比如让零件与炉子一起冷下来。
Applying the method of Lagrange multiplier, the system is optimized for maximum cooling rate and gets the rate general expression.
运用拉格朗日乘数法，以最大制冷量为优化目标，对该系统进行了优化，得到最大制冷量的一般表达式。
The influences of cooling rate after the forge on the heating temperature and time of apheroidized annealing of steel T10 was studied.
研究了锻造后的冷却速度对T10钢等用球化退火加热温度和保温时间的影响。
The metastable zone was measured by laser method and the effects of cooling rate and agitation speed were investigated experimentally.
采用激光法测定了甘氨酸的结晶介稳区，并分别考察了降温速率和搅拌速率对其介稳性质的影响；
The temperature distribution field and its variation rule was being simulated by controlling environmental temperature and cooling rate.
通过控制环境温度和冷却速度，模拟厚大断面球墨铸件凝固过程温度场的分布和变化规律。
Steel grain-reinforced pure copper cast composite was gotten successfully by suspension casting process and controlling the cooling rate.
采用悬浮浇铸工艺并控制冷却速度成功地得到了钢颗粒增强纯铜基铸造复合材料。
The effects of opening flask temperature and cooling rate on low and high temperature age-hardening alloy casting are tested and studied.
试验研究了开箱温度和冷却速度对低、高温时效型合金时效硬化效果的影响。
Food vacuum cooling equipment is a new type boiled food production equipment which has quick cooling rate, even cooling effect and health.
食品真空冷却装置是一种冷却速度快，冷却效果均匀、卫生的新型熟制食品生产设备。
The quantitative relationship between secondary dendrite arm spacing and solidification cooling rate of AZ91 was obtained by regressive analysis.
用数学回归的方法得到了AZ91镁合金的凝固冷却速度与二次枝晶间距的定量关系式。
The effect of cooling rate and undercooling temperature on the rate and amount of dehydrogenation was studied by magnetic balance simulation method.
用磁秤模拟方法研究了冷却速度和过冷温度对镍铬钢排氢速度和排氢量的影响。
The strip cooling rate with hydrogen and hydrogen plus water spray on continuous annealing line is estimated according to the heat transfer principle.
利用传热学原理估算了带钢连续退火生产中采用氢气和氢气加雾化水冷却介质的冷却速度。
The strip cooling rate with hydrogen and hydrogen plus water spray on continuous annealing line is estimated according to the heat transfer principle.
利用传热学原理估算了带钢连续退火生产中采用氢气和氢气加雾化水冷却介质的冷却速度。
应用推荐