• The main method to control crack formation is to utilize the techniques from design, construction and material, which can control the crack size within a safe scope.

    裂缝控制的主要方法是通过设计、施工、材料等方面综合技术措施将裂缝控制在无害范围内。

    youdao

  • The mechanism of crack formation caused by the 'pegs' is also discussed.

    文中还分析了裂纹产生机制。

    youdao

  • If the soldered joints are exposed, check for visible signs of crack formation.

    如果露出了焊接点,检查是否形成了裂纹。

    youdao

  • The effect of the shape of electrode tip on crack formation and sticking were investigated.

    研究了电极端部形状对焊点产生裂纹及粘结的影响。

    youdao

  • The crack formation of thermal shock fatigue is related to the nucleation, growth and join of microvoid.

    热冲击疲劳裂纹的形成与微孔洞的形核、长大和连通有关。

    youdao

  • By observing and analyzing cold punching process at the factory, the cause of the crack formation was found.

    通过对冷冲压过程的实地观察分析,找准了裂纹产生的原因。

    youdao

  • The cause of crack formation in construction of prefabricated t beams of a certain prestressed bridge is analysed.

    分析了某预应力桥梁预制T梁施工裂缝产生的原因。

    youdao

  • The paper puts forward the corresponding measures for prevision of cracks from the study on crack formation mechanism.

    该文从裂缝形成机理的研究,有针对性地提出了预防裂缝出现的相应措施。

    youdao

  • For over-long reinforced concrete frame structure, temperature loading often leads to crack formation of the beams and plates.

    对于超长钢筋混凝土框架结构,变温的作用常常导致混凝土梁和楼板的开裂。

    youdao

  • Pointing out the main reason of crack formation is that casting blank is not up to standard and the strength of parts is not enough.

    指出铸造的毛坯件不合格及零件本身强度不高是产生裂纹的主要原因。

    youdao

  • Based on in-depth analysis of reflective crack formation mechanism, this paper gives reflective crack preventive and curative measures.

    本文在深入分析反射裂缝形成机理的基础上,提出了反射裂缝的预防及治理措施。

    youdao

  • The results showed that failure morphology was of typical contact fatigue characteristics, and two modes of fatigue crack formation worked.

    结果表明,失效形貌呈典型的接触疲劳特征,两种疲劳裂纹形成模式同时存在。

    youdao

  • The research results showed that the slab surface temperature dropping into the third brittle zone played an important role in causing transverse crack formation ofm...

    研究表明,铸坯表面温度落入钢的第三次脆性温度区是造成铸坯表面横裂的一个重要原因。

    youdao

  • Analysis is made on the causes of crack formation of prestressed concrete structure and on the influencing factors on its structural durability, and given the preventions.

    分析造成混凝土结构裂缝的主要原因及裂缝对混凝土结构的耐久性的影响程度。并提出了预防和控制混凝土结构裂缝的工程措施。

    youdao

  • A finite element computer program for saturated soils was revised accordingly in order to be used in the analysis of crack formation and propagation upon drying on the clay surface.

    相应的修改了饱和土的有限元程序,用于分析粘土表面干缩裂缝的形成过程。

    youdao

  • The research results showed that the slab surface temperature dropping into the third brittle zone played an important role in causing transverse crack formation of microalloyed slab.

    研究表明,铸坯表面温度落入钢的第三次脆性温度区是造成铸坯表面横裂的一个重要原因。

    youdao

  • The research results showed that the slab surface temperature dropping into the third brittle zone played an important role in causing transverse crack formation of microalloyed slab. E…

    研究表明,铸坯表面温度落入钢的第三次脆性温度区是造成铸坯表面横裂的一个重要原因。

    youdao

  • The research results showed that the slab surface temperature dropping into the third brittle zone played an important role in causing transverse crack formation of microalloyed slab. E…

    研究表明,铸坯表面温度落入钢的第三次脆性温度区是造成铸坯表面横裂的一个重要原因。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定