To transfer instrument commands and data on the bus, the Controller addresses one Talker and one or more Listeners.
为了在总线上传输仪器命令和数据，控制器给一个呼叫口和一个或几个响应口分配地址。
A computer bus provides parallel data transfer.
计算机总线可以传输平行数据。
In chapter four, describes the bus management, and discussed the implementation of data transfer, flow control and error control in the network-stye instrument bus.
第四章讨论总线管理，阐述了数据传输、流量控制和差错控制在网络式仪器总线中的实现。
This interface uses a peer-to-peer architecture in which peripherals negotiate bus conflicts to determine which device can best control a data transfer.
这种接口采用点对点架构，外周设备协商解决总线冲突问题，以确定哪个设备控制数据传输最佳。
The data transfer rate between varied boards in radar signal processors based on VME or CPCI bus was limited by the bus rate.
在基于VME总线或CPCI总线的雷达信号处理机中，板与板之间的数据传输速率受限于总线的速率。
A data collecting method with general parallel port can be used in many occasions. Its data transfer rate approaches the rate of ISA bus.
本文提出了一种使用通用并口进行数据采集的方法，能在多种场合下使用，其数据传输率可以接近IS A总线。
Because of its separate structure between microprocessor bus and DMA bus, the recorder achieves higher data transfer rate.
由于采用分离的微处理器总线和DMA总线结构，因此实现较高的数据存储速率。
While reforming CPCI bus transfer to network data transfer, the thesis brings forward and implements "transfer without interference", registration and management of boards, Hot-Swap, etc.
本文在将CPCI总线传输改造成网络数据收发的过程中提出并实现了“无干扰传输”、总线板卡注册管理、热插拔等解决方案。
The ICS message bus and mailbox are used in application layer of the software architecture, which make it easy to transfer data and communicate each other between processes.
在应用层开发上研发任务间通讯服务（ICS）消息总线和邮箱服务，承担模块化设计的各功能进程的通讯控制和数据交互。
Nodes are connected to CAN bus through the adapter of intelligent network, resulting in timely, exact and reliable transfer of multifold main architecture network data.
节点通过智能网络适配器连接到CAN总线上，从而实现了多主结构网络数据的及时、准确、可靠传递。
Using USB bus to transfer data blazed a way in communication between data acquisition system and computer.
使用USB总线传输数据，为数据采集系统与计算机之间的通讯开辟了新的道路。
Off-chip memory latency is mainly determined by DRAM latency, and memory bandwidth is determined by data transfer rate through the memory bus.
片外存储系统的访存延迟主要由DRAM延迟决定，带宽则是由内存总线的数据传输率所决定。
Meanwhile, the system USES the mature CAN bus to realize the data transfer system with wire and wireless.
同时，系统中利用了现在已经较成熟的CAN总线技术，实现了有线和无线相结合的数据传输系统。
We choose USB (Universal Serial Bus) as the communication interface of DSP and the computer which can fulfill up data transfer and the control to DSP.
系统选用USB(通用串行接口)作为和上位机通信的接口，实现处理数据的上传以及上位机对DSP的控制。
It is installed in ISA bus of PC. It USES long distance drive technique to realize the correct data transfer when the cable connecting the two computers is over 150 metres.
它安装在微机的IS A总线上，并采用了长线驱动技术，保证连接两机的电缆在150米以上都能进行正确的数据传送。
To be more specific, the detailed data transfer agreement and the interface software plan for CAN bus communication are discussed on the basis of aluminum reduction requirements.
根据铝电解生产的特点详细讨论了传输的数据约定协议，给出了CAN总线通信接口软件设计方案。
Asynchronous First In First Out (FIFO) is adopted to synchronize data transfer between APB bus and I2C bus.
设计中采用了异步先进先出来同步apb总线和I2C总线之间的数据交换。
Data transfer operations are protected by CRC codes; therefore, any bit changes induced by card insertion and removal can be detected by the SD bus master.
数据传送操作是通过CRC编码来保护的，因此，由拔插卡引起的任何位的变动将会被SD总线管理器侦测到。
Data transfer operations are protected by CRC codes; therefore, any bit changes induced by card insertion and removal can be detected by the SD bus master.
数据传送操作是通过CRC编码来保护的，因此，由拔插卡引起的任何位的变动将会被SD总线管理器侦测到。
应用推荐