This paper introduces the parameter estimation research for the turbine inlet temperature and compressor exit pressure by using the engine variables measured under the different flight conditions.
本文研究利用不同飞行状态下测量的发动机变量估计涡轮进口温度和压气机出口压力。
These factors make the die exit pressure, normal velocity and shear rate not to be zero, thus lead to problems including die swell and etc.
这些影响因素使得口模出口处压力、法向速度和剪切速率均不为零，从而引发离模膨胀等问题。
This exit pressure is then used to identify the kind of tissue in which the injection is being introduced.
然后采用该出口压力识别将要接受注射的组织类型。
Changes of sidewall sweep Angle and cowl position can influence inlet performance such as mass capture, total pressure recovery coefficient and uniformity of isolator exit flow field.
侧板后掠角大小和整流罩位置变化时，对进气道的质量捕获、总压恢复系数和隔离段出口流场的均匀性等都有一定的影响。
The compressor exit total pressure is adopted as a characteristic signal to detect surges. An ar (autoregressive) model is constructed with the time series analysis method.
以压气机出口总压作为喘振检测特征信号，采用时间序列分析方法建立了AR模型。
The distributions of the pressure, the front tension stress, the back tension stress and the exit lateral displacement of each pass are given out.
得到了各道次单位轧制压力、前后张应力和出口横向位移的分布。
The discrete vortex method was adopted to simulate and analyze the vortex structure and pressure distribution of the flow field at the nozzle exit.
采用离散涡方法模拟了两种不同形状哨嘴的喷嘴出口流场旋涡结构和压力分布。
Comparisons were also made between computational and experimental data of pressure distribution on the wall of the mixing duct and velocity distribution on the exit of the duct.
并对混合管壁面的压力分布和出口速度型与实验值进行了比较。
The influence of the bite, the entrance and exit elastic deformation and the roller both ends contact pressure is considered. The formula is convenient and precise.
本公式考虑铝箔入口和出口弹性变形和轧制铝箔两侧轧辊辊身端部弹性接触压力对轧制力的影响。本公式计算精确而且简便。
In the experimental study, the pressure surge data are acquired at 26 points from the taper pipe intake to the draft tube exit distributing at 8 sections under 6 stable operating conditions.
对水轮机模型，测取了从直锥段进口至尾水管出口8个截面共26个测点在6个稳定运行工况下的水压力脉动数据。
Using resistance strain gage, dynamic pressure sensor, slip ring and tape recorder, the blade vibration strain and exit pressure signals of rotor blades are recorded and then processed.
利用电阻应变片、动态压力传感器、滑环式引电器和磁带记录仪等，录取叶片振动应变和动叶出口压力信号，然后回放磁带，做信号处理。
Test results show lower exit average total pressure recovery, larger circumferential total pressure distortion and stronger and more irregular secondary flow.
试验表明其出口平均总压恢复系数较低，周向总压畸变指数较大，旋流较强且很不规则。
The increase of lobe diffusion angle results in the increase of velocity circulation at the lobe exit section, but it raises the mixing loss and lowers the pressure recovery coefficient.
扩张角的增加可提高速度环量，但是流动混合损失增加，总压恢复系数减小。
The enlarged joints and related degenerative changes place pressure on the nerve roots as they exit the spine.
增生的关节和相关退行性改变对即将离开脊柱的神经根造成压迫。
The faster its exit, the lower the air pressure beneath the car, and hence the more downforce the car generates.
气流通过底盘速度也快，底盘下方空气压力越低，因此赛车获得的下压力越大。
Flame stability has no relation with the ethylene guide flame, and the exit chocking ratio is an important factor for the combustor pressure rising.
同时发现火焰稳定与乙烯引导火焰无关，出口堵塞比是燃烧室压力提升的一个重要影响因素。
For the limitations of exit static pressure of fan coil, the deviation between designed and actual resistance will impact on the wind.
风机盘管机组由于出口静压的局限性，一旦设计阻力与实际阻力有偏差，对风量会产生很大影响。
Experimental results showed that the effective pressure distribution of the exit section was different and the flow friction decreased due to the influence of film bleeding.
结果表明：通道出口段存在气膜出流与无气膜出流情况相比出口段有效压力分布发生变化，并且使整个通道的流阻下降。
The optimum jet distance for jet pressure pulsation was about 7-14 times of nozzle exit diameter.
实验还表明，自激振荡脉冲喷嘴射流存在最优喷距，最优喷距的大小为喷嘴出口直径的7～14倍。
Passenger vehicle one-way control, separation of the entrance and exit, benefit for reducing the pressure on the surrounding traffic.
客运车辆单向控制，出入口分离，有助降低周边交通压力。
To control foundation seepage and exit gradient, a plastic concrete cut-off wall, a grout curtain, and a set of downstream pressure relief Wells are incorporated in the design.
为了控制基础渗流和出逸坡降，设计采用了塑性混凝土防渗墙、帷幕灌浆以及在下游增设一套减压井相结合的方案。
In the pyrogenic production procedure, negative pressure may exit in gas equipment and containers and consequently damage them.
在焦化生产过程中，煤气设备及容器内容易出现负压而造成设备损坏。
In the pyrogenic production procedure, negative pressure may exit in gas equipment and containers and consequently damage them.
在焦化生产过程中，煤气设备及容器内容易出现负压而造成设备损坏。
应用推荐