Seal welds shall be welded with half the thickness of the carrying fillet weld.
密封焊道应焊成现填角焊缝厚度的一半。
The weld can be divided into four types: butt weld, fillet weld, plug weld and end weld.
焊缝可分为对接焊缝、角焊缝、塞焊缝和端接焊缝四种。
An automatic CO2 welding device for elbow pipe and flange fillet weld joint is introduced in the paper.
介绍一种弯管和法兰角接接头填角焊的自动焊接装置。
Non-watertight weld joints and fillet welding for stiffening member shall be painted after block inspection.
加强构件的非水密焊接接合和填角焊应该在检查完分段后进行喷漆。
The basic stress of T-fillet weld is analyzed, the safe measures for it in design, welding and corrosion control are presented.
分析了T形角焊缝部位的基本受力状况，对该部位容易出现的问题进行了分析，从设计、焊接、防腐等方面提出了应对措施。
Weld-shape(butt weld width, size of fillet weld)is an indicator of weld features and it also is an important factor of quality welding.
焊缝尺寸 （如对接焊缝的焊缝宽度、角焊缝的焊角尺寸等 ）是表示焊缝形状特征的指标 ，是影响焊缝质量的重要因素之一。
The strength of fillet welding joint is related not only to the fillet weld size, but also depends on the base metal strength matching.
角焊缝的强度不仅与焊脚尺寸有关，还取决于焊缝金属与母材强度的匹配。
Value of torsion for less than the size of fillet weld height of small-opening fillet weld is the same as that of corresponding closed fillet weld.
具有不大于焊脚尺寸的小开口焊缝，其所能承受的扭矩与相应闭合角焊缝所能承受的扭矩是几乎相同的。
This paper briefs the fractures of fillet weld of manhole reinforcing plate in react ion tower of thermal cracking plant and its repairing welding.
本文简要介绍了热裂化装置反应塔入孔加强板角焊缝的断裂及其补焊情况。
For the T-fillet weld, there are high stress, difficult to weld, more defects and easy to be corroded in vertical oil tank, which is often neglected.
大型立式油罐t形角焊缝部位应力高，施工难度大，焊缝存在缺陷多，容易受到腐蚀，而且常被忽视。
It is also proved theoretically that the deduced method for fillet weld connections meets the requirement of the probabilistic limit state design procedures.
从理论上证明角焊缝连接的折算方法满足概率极限状态设计要求。
By analyzing and discussing design of fillet weld connection, a comment is presented and some useful Suggestions on design of fillet weld connection are given.
通过对角焊缝连接设计的分析讨论，提出一个值得探讨的问题，并就角焊缝连接设计给出一些有益的建议。
It is also proved theoretically that the deduced method for fillet weld connections meets the requirements of the probabilistic limit states design procedures.
从理论上证明角焊缝连接的折算方法满足概率极限状态设计的要求。
Radiographic examination was performed with portable X-ray fault detector appling the special radiographic technique for fillet weld of heat exchange tube-tubeplate.
用普通便携式X射线机，采用特殊的透照技术，对换热管与管板角焊缝进行射线检测。
Campared with the original composition, the new composition system has more steady flowing, better article glossiness and flexibility, and higher fillet weld strength.
在加工过程中与原配方比较，料流稳定，提高了制品的光泽度、柔韧性及焊角强度。
Butt welds qualify full and partial penetration butt welds and fillet welds. Fillet weld tests shall be required where this is the predominant form of production welding.
对接焊缝可评定全焊透和部分焊透对接焊缝和角焊缝，当角焊缝是产品的主要焊接接头形式时，需要用角焊缝试验评定。
And the welding connecting of them are advised to use slope butt weld that are fully welded, but when the double-sided fillet weld is used, they should be design on equal strength.
节点中的焊接宜采用完全焊透的坡口对接焊缝连接，当采用双面角焊缝连接时，可按等强设计。
The influences of strength matching on fillet weld were analyzed. The relationships among fillet weld size, thickness of base metal and matching coefficient of strength were established.
分析了强度匹配对角焊缝设计的影响，建立了角焊缝焊脚尺寸与板厚，强度匹配系数之间的关系，讨论了强度匹配选择的依据。
Through the pipe sample cutting and analyzing the crack in the fillet weld between the hot reheat pipe and the warming pipe, it was found out that the cause of the crack is due to the thermal fatigue.
通过对再热热段至低旁暖管管道角焊缝上裂纹的解剖分析，其原因是热疲劳裂纹引起的。
The elements can be put together in various ways. For example, a lap join may be held by a fillet, plug, or slot weld, and and a tee joint by a fillet or groove weld.
这些元素可以以不同方式组合在一起，例如：一个搭接接头可能用角接、塞焊和缝焊固定，一个丁字接头可以用一个搭接或槽焊来完成。
The elements can be put together in various ways. For example, a lap join may be held by a fillet, plug, or slot weld, and and a tee joint by a fillet or groove weld.
这些元素可以以不同方式组合在一起，例如：一个搭接接头可能用角接、塞焊和缝焊固定，一个丁字接头可以用一个搭接或槽焊来完成。
应用推荐