• Draw the element for maximum shear stress and mark values of all stresses.

    画出最大剪应力的单元体并标出全部应力值。

    youdao

  • The straightforward procedures to achieve shear modulus of colloform and maximum shear stress are specified.

    提出了求解胶体剪切模量和最大剪应力的简单方法。

    youdao

  • The research results show that the maximum shear stress of dual-phase steel raises with the increase of martensite content.

    研究表明,随着马氏体含量的增加,双相钢的最大剪切应力随之增加。

    youdao

  • It will decrease the maximum axial stress of the lining, but it will increase the maximum shear stress and flexural stress.

    开挖引致的松动区减少围岩劲度,将减少衬砌轴向应力,但增加剪应力及挠曲应力。

    youdao

  • Then the stress distribution of anchored rock mass with partial pull-out failure is analyzed based on the maximum shear stress criterion.

    基于最大剪应力破坏准则,分析了局部脱粘破坏锚固体的应力分布。

    youdao

  • The results show that the distributing of the maximum principal stress and maximum shear stress are mainly under the control of the landform and fault.

    结果显示,隧址区的最大主压应力及最大剪应力分布主要受地形和断层的控制。

    youdao

  • The fatigue resistance of the butt welds can be improved by means of removing the weld reinforcement and designing the weld in the maximum shear stress plane.

    去除焊缝余高或将焊缝设计在最大剪应力平面内可明显改善对焊接头的疲劳性能。

    youdao

  • The calculation indicates that the maximum shear stress around inclusion is 1.2-1.7 times of that without inclusion, which has a harmful effect on the fatigue endurance of rail.

    计算发现,夹杂物周围的最大剪切应力是不含夹杂物时的1.2~1.7倍,这对钢轨疲劳寿命造成有害影响。

    youdao

  • Around the propagating fault segment the disturbed stress field of maximum shear stress displays an eight petal pattern and that of mean stress displays a four quadrant pattern.

    围绕断层扩展部位剪应力增量场呈八瓣式分布,平均应力增量场呈四象限分布。

    youdao

  • The stress accumulation in the southeastern segment of the fault since 1893 has been calculated, and the corresponding contours of maximum shear stress and hydrostatic stress are shown.

    计算了1893年以来在断裂带南东段(相对闭锁段)的应力积累,示出相应的最大剪应力和流体静应力等值线图。

    youdao

  • Maximum shear stress generally takes place at the neutral axis of ship section.

    最大剪应力通常发生在剖面的中和轴处。

    youdao

  • Maximum shear stress generally takes place at the neutral axis of ship section.

    最大剪应力通常发生在剖面的中和轴处。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定