During the course of forming the welding spot, checking and controlling spot welding current value is the key to assure the welding quality.
在焊点形成的过程中，点焊电流有效值的检测与控制是保证焊接质量的关键。
The calculation of spot welding current is determined by the way of point-by-point integration, the software and hardware system is constituted based on 80c196kc single chip computer.
确定了以逐点积分法作为电流有效值的计算方法，建立了以80c196KC单片机为中心控制器件的软件、硬件系统。
On the basis of digital signal process and nondestructive testing, the effect of welding process on the frequency spectrum of the current signal in AC spot welding is analyzed.
在数字信号处理及无损检测的理论基础上，分析了焊接过程对电流信号频谱的影响。
Spot welding is greatly affected by the current, so the real-time display of current waveform in the welding is very necessary.
焊接电流对电阻点焊有着重要的影响，因此在点焊过程中实时显示焊接电流波形是十分必要的。
The accurate measurement of welding current and voltage is very important to the exact control of resistance spot welding inverter and welding quality.
焊接电流与电压的准确测量对精密控制逆变电阻点焊电源和保证焊接质量至关重要。
This paper introduced a portable instrument to check and measure spot welding machine's current by the MSP430 MCU.
本文介绍了一种用MSP430单片机实现的对点焊机电流进行检测的便携式仪器。
The spot welding tests prove the microcomputer control system has satisfactory constant current monitoring effect under different main voltage and load conditions.
并通过不同网压和不同负载下的点焊试验，证明该微机系统可获得满意的恒流监控效果。
Spot welding requires both an electric current and a forging pressure to produce the weld.
点焊需要电流及锻压来产生焊缝。
This paper deals with the development of the microcomputer constant current control system of the spot welding inverter.
本文研制逆变点焊电源的微机恒流控制系统。
Employing higher current and shorter welding time is benefit for austenite stainless steel spot welding.
采用大电流、短时间的焊接参数是较为合适的规范。
The design, analysis and testing of the welding current signal detecting circuit for spot welding machine are discussed in this paper.
本文主要论述点焊机焊接电流信号检测电路的设计、分析和测试。
The main characteristics of minisize piece spot welding is analyzed. The basic principle, output current waveform and properties of various minisize piece spot welding machine is expatiated.
分析了微型件点焊的主要特点，阐述了各种微型件精密点焊机的基本工作原理、输出电流波形和性能特点。
A controlling model of inverter spot-welding process and a fuzzy neural network configuration about inverter spot-welding with constant current control were built in this paper.
推导了逆变点焊过程控制模型，并构建了逆变点焊模糊神经网络恒电流控制系统结构。
The linearity, wave distortion, temperature influence, and its compensation measure in detecting current during spot welding by hollelement are described in this paper.
论述了霍尔器件检测点焊焊接电流时的线性度、波形失真、温度的影响及其补偿措施。
This topic carries on the constant current control to the resistance spot welding process using a system of single chip computer, whose core has used the C8051F005.
本文的研究工作利用单片机控制系统对电阻点焊过程进行恒流控制，其核心采用了集成度英明、助能强的C8051F005单片机。
This paper introduces a control system of spot welding constant current based on fuzzy logic arithmetic.
介绍了一种基于模糊逻辑算法的点焊恒电流控制系统。
The result of testing on site manifests that the effect of spot welding constant current control is good.
实际焊接考核试验结果表明：控制系统具有很好的恒流控制效果。
For this issue, the method, which is the quality controlling of spot welding in the external direct current magnetic field, will be discussed by this article.
针对这个问题，本文探讨了外加直流磁场改善点焊质量的方法。
The automatic machine of anode current collector and bottom plate spot welding was designed and prepared successfully.
报导了碱锰电池负极集流体自动焊接机的研制。
Controlling the conduct Angle of the silicon symmetric switch controls the output of the electric current for spot welding.
用控制可控硅导通角来控制焊接电流的输出。
The parameters of heating rate, energy, current waveform and time should be controlled precisely in order to insure the quality of minisize piece spot welding.
为了确保微型件点焊质量，往往需要对点焊过程的加热速度、能量、电流波形、时间等参数进行精密控制。
Study on control system of spot welding constant current based on fuzzy logic arithmetic;
提出了一种用模糊逻辑算法实时控制图像编码比特率的方法。
Study on control system of spot welding constant current based on fuzzy logic arithmetic;
提出了一种用模糊逻辑算法实时控制图像编码比特率的方法。
应用推荐