Fasteners, the bolt tightening torque of 65 n. M, shall not be destroyed.
采用的扣件，在螺栓拧紧扭力矩达65n.m时，不得发生破坏。
Even when loosened by 45 degrees, more than half of the tightening torque remained.
甚至在螺母松脱45度的情况下，其一半以上的锁紧扭矩仍然不变。
The equation for calculating minimum tightening torque on the crank pin nut is given.
给出了曲柄销联接螺母的最小拧紧力矩计算公式。
Tightening torque is one of the main factors that affect the connection quality in threaded connections.
油套管联接过程中，拧紧扭矩是影响油套管联接质量的主要因素之一。
Sensor bolt to be used to ensure a certain degree of tightening torque, prolonged use will not become loose.
传感器要采用螺栓固定，保证一定的紧固力矩，长时间使用不会松动。
Always check the assembly drawing for confirmation as tightening torque values on the drawing takes precedence.
始终检查组装图以确认图上的拧紧力矩值优先。
This article proposes that the tightening torque design should be made based on the requirements during bolts design.
本文提出在进行螺栓设计时应根据需要或要求对紧固力矩进行设计。
It is pointed out the value of tightening torque should guarantee that there is no slippage between cylinder and rasp bar when they work.
脱粒滚筒与纹杆间螺栓联接的扭紧力矩值应按保证工作时滚筒与纹杆间不发生滑移来确定。
The value of tightening torque is relative not only to the nominal diameter and quality class of the bolt, but also to the security of the threaded fastener.
指出螺栓联接的扭紧力矩值不仅与螺栓的公称直径及性能等级有关，还与能否保证联接可靠工作有关。
Changing the positions of thin and thick nuts and using the right thick nut tightening torque ensure safe operation of the crane and longer lives of the screws.
通过试验和理论分析厚、扁螺母在紧固过程中的受力情况，并从试验结果得到一个较合理的厚螺母拧紧力矩，既能保证塔式起重机的安全运行，又能延长螺栓的使用寿命。
The paper analyzed the bolt pre-stress affected to the mine roadway support effect and the relevant relationship between the bolt pre-tightening torque and the pre-tension.
分析了锚杆预应力对巷道支护效果的影响，锚杆预紧扭矩与预紧力对应关系。
This article studies the influence of the bolt tightening torque on the fretting damage of LY12CZ aluminium alloy double shear lap bolted joint by experimental and conumerical analysis.
从试验和数值分析两个方面研究了螺栓预紧力矩对LY12CZ铝合金双盖板对接螺纹联接件微动损伤的影响。
Thus, torque wrenches should be used for tightening DISS connections. The recommended tightening torque is 35 foot-pounds with a nickel DISS washer and 12 to 15 foot-pounds for a CTFE washer.
因此，应该使用转矩扳手来上紧diss接头。推荐的上紧转矩对于镍DISS垫圈是35英尺-磅，对于CTFE垫圈是12到15英尺-磅。
The force and distortion of a new type locking rings unit were analyzed. The tightening torque and other performance figures were calculated, which provides theoretical basis for its proper usage.
对新型精轧机辊环锁紧装置进行了受力和变形分析，计算出它的拧紧力矩和相关性能指标，为正确使用提供了相关的理论依据。
In the manufacturing and assembly world, tightening, controlling, or measuring torque fasteners is imperative for production efficiency.
在制造和装配领域中，绷紧，控制，或测量扭矩紧固件的生产效率是当务之急。
Metal construction. jointing by means of bolts with controlled tightening. calibration of torque wrenches.
金属结构。可控拉紧螺栓连接。扭力扳手校准。
If possible, a torque wrench should also be used for tightening.
如果可能，扭力扳手，应该也可用于收紧。
After provisional tightening by an air motor at high speed, final torque set is performed manually.
扭力扳子内装气动马达，从预紧固到最终紧固，一次操作完成即可。
You can refine your "calibrated elbow" by using a properly maintained torque wrench a few times a month for common jobs like tightening that drain plug.
通过类以紧固油底壳螺栓这样的日常工作，一个月多次应用合适的维修扳手您可以优化您的“校准肘”的精确度。
NSK-I type of controller of the tightening up a screw machine is a new type of the torque controller. It has achieved continuous adjustment to the torque of the controlled motor.
型拧丝机控制器作为一种新型的力矩控制器，实现了对被控电动机力矩的连续调节。
In some cases, a torque versus Angle yield method is utilized, particularly when tightening 16 mm and larger sizes.
在某些情况下，特别是在紧固16mm及以上尺寸时，要采用扭矩与角度输出量关系的方法。
The first tightening shall be carried out at 60% of the expected torque.
第一步，用期望扭矩值的60%进行拧紧。
Thus, torque wrenches should be used for tightening DISS connections.
因此，应该使用转矩扳手来上紧diss接头。
Thus, torque wrenches should be used for tightening DISS connections.
因此，应该使用转矩扳手来上紧diss接头。
应用推荐